
Produk
Chaff Cutter & Forage Processor
Cut, shred and grind fresh or dry forage for cattle, sheep and goats. 19 models and ranges below; outputs depend on material, moisture and configuration — confirm with a trial sample.
Perbandingan model
| Model | Tipe | Daya | Kapasitas | Tegangan | Berat |
|---|---|---|---|---|---|
| WY-0.4-G200 | Chaff cutter & grinder | 2.2 kW | 600-1000 kg/h | 220 V / satu fasa | 101 kg |
| WY-93QS-2A | Chaff cutter berpenggerak rantai | 3 kW | 2-2.5 t/h | 220 V / satu fasa | 76 kg / tanpa motor |
| WY-93QS-2S | Chaff cutter berpenggerak rantai | 3 kW | 3 t/h | 220 V / satu fasa | 75 kg / tanpa motor |
| WY-93QS-3.8 | Chaff cutter berpenggerak rantai | 5.5 kW | 3-5 t/h | 380 V / tiga fasa | 78 kg / tanpa motor |
| WY-93QS-4.8 | Chaff cutter berpenggerak rantai | 5.5 kW | 4-4.8 t/h | 380 V / tiga fasa | 86 kg / tanpa motor |
| WY-9QS-2 | Chaff cutter berpenggerak rantai | 3 kW | 2000-2500 kg/h | 220 V / satu fasa | 76 kg / tanpa motor |
| WY-9QS-300S | Prosesor pakan 4-in-1 | 3 kW | 800-1000 kg | — | 55 kg |
| WY-9ZF-50 | Mesin pemotong / pencacah / penggiling | 3 kW | 0.6-1 t/h | 220 V / satu fasa | 50,8 kg / tanpa motor |
| WY-9ZT-0.4 | Chaff cutter berpakan konveyor | 2.2 kW | 0.4-1 t/h | 220 V / satu fasa | 39,9 kg / tanpa motor |
| WY-9ZT-0.4A | Chaff cutter | 2.2 kW | 0.6-1 t/h | 220 V / satu fasa | 43 kg / tanpa motor |
| WY-9ZT-0.4AG | Chaff cutter | 2.2 kW | 0.4-1 t/h | 220 V / satu fasa | 46 kg / tanpa motor |
| WY-9ZT-0.4B | Chaff cutter berpakan konveyor | 2.2 kW | 0.4-1 t/h | 220 V / satu fasa | 45,5 kg / tanpa motor |
| WY-9ZT-0.4C / WY-9ZT-0.4Q | Pemotong jerami berpengumpan hopper | 2.2 kW | 500-800 kg/h | 220 V / satu fasa | 50 kg / tanpa motor |
| WY-9ZT-0.4S | Chaff cutter | 2.2 kW | 0.4-1 t/h | 220 V / satu fasa | 52 kg / tanpa motor |
| WY-9ZT-0.6S | Chaff cutter multi-drive | 2.2 kW | 0.4-1 t/h | 220 V / satu fasa | 56 kg / tanpa motor |
| WY-9ZT-3G | Chaff cutter | 3 kW | 300-400 kg/h | 220 V / satu fasa | 79 kg / tanpa motor |
| WY-9ZT-6.5 | Chaff cutter berpenggerak rantai | 7.5 kW | 5-6.5 t/h | 380 V / tiga fasa | 193 kg / tanpa motor |
Pertanyaan yang Sering Diajukan
Bagaimana saya tahu mesin ini cocok untuk bahan dan kapasitas output saya?
Ilustrasi bahan dan simbol proses dalam katalog hanya untuk referensi. Konfirmasi kesesuaian dan kapasitas keluaran dengan sampel uji; sampel, konfigurasi, serta persyaratan penerimaan disepakati sebelum produksi.
Bagaimana cara saya mendapatkan penawaran harga?
Bagikan model, jumlah, dan tujuan pengiriman Anda, lalu kami akan siapkan penawaran khusus. Syarat perdagangan (EXW / FOB / CIF) dan syarat pembayaran dikonfirmasi dalam penawaran. Situs web: www.weiyanmachinery.com
Waktu tunggu?
Dari pemesanan hingga pengiriman: waktu tunggu khas 15–35 hari.
Jadwal pengiriman akhir tergantung pada jumlah pesanan.
Pengaturan pengemasan dan pengiriman dikonfirmasi untuk setiap pesanan.
Syarat perdagangan?
Ketentuan perdagangan fleksibel: EXW / FOB / CIF.
Pilih ketentuan pengiriman yang sesuai dengan rencana pengadaan Anda.
Syarat pembayaran dikonfirmasi dalam penawaran harga.
铡草机运行噪音大的原因与判断方法??
动刀紧贴定刀运行时产生的声音属正常现象,尤其新机磨合期更明显;新机应加注齿轮油/润滑脂并确保齿轮对齐。若出现敲击声或观察到齿轮弯曲,请发送视频和照片以便进一步检查。
铡草机切割长度能否调节?如何调节??
部分型号无齿轮调节杆,其切割长度为固定值,约5–30 mm(单位为毫米,非厘米);如需调节切割长度,须选用带齿轮换挡杠杆的型号。请提供具体型号以便确认。另:若固定板开裂,可拆除且不影响使用;若草料落入电机区域,可在新订单中加装挡板。【待核实:固定板可拆除、挡板仅单一出处】
售后第一步:客户报修时应提供哪些信息??
客户报修时,需提供:清晰的照片 + 运行视频(显示故障现象)、机器型号、订单号/批次号、具体故障部位。这有助于判断问题属于运输、装配、操作还是质量问题,并据此发送对应指导(如调整视频、接线图、装配PDF);若需更换零件,售后团队将跟进处理。
铡草机切草过长或切割不良的原因与处理方法??
通常因动刀与定刀间隙变大所致(使用磨损、喂入石块或人为移动刀片)。处理方法:断电后松开定刀螺栓,将定刀向动刀方向推近(动刀应刚好接触定刀),再拧紧;用一张A4纸测试间隙。所有铡草机使用一段时间后均需进行刀片间隙调整。出厂时已预设间隙,终端用户不应随意移动刀片。可提供刀片调整视频。
铡草机堵料、停转或跳闸的原因与处理方法??
原因与处理包括:1)单次喂料量过大;坚硬秸秆需减慢喂入速度;2)断电后清理出料口;3)皮带打滑时需张紧;4)电机转速应约为2800 rpm(若为1440 rpm电机,需配不同皮带轮);5)供电电缆截面积至少2.5 mm²且尽量短;电压过低会导致堵转和跳闸;6)检查刀片间隙。若皮带严重磨损,需更换。
铡草机大齿轮偏移、晃动或齿损坏的原因与处理方法??
齿轮偏移通常由运输挤压或超负荷运行引起。若仅偏移或晃动,可用锤子轻敲使其与小齿轮对齐,对准标记后加注润滑脂,并减少单次喂料量;可提供齿轮调整视频。若齿轮出现裂纹或断齿,请发送照片,售后团队将跟进更换零件。
铡草机皮带不匹配、打滑或皮带轮开裂/松动的原因与处理方法??
安装皮带时应先装好皮带,再边转动皮带轮边拧紧电机固定螺栓;同时检查机架是否反向安装。对于型号2000-COMBO,正确皮带规格为A920 + A1120。需确认电机皮带轮内孔尺寸与电机轴匹配。若皮带或皮带轮尺寸错误、开裂或缺失,请发送该零件及其标识文字的照片,售后团队将跟进处理;可提供装配视频。
电机过热、跳闸或烧毁的原因与处理方法??
多数情况源于电源或过载:1)供电电缆过细(<2.5 mm²)或过长,或电压偏低——应改用更粗、更短的电缆;2)大功率电机不可经插头插座供电,须直接接入MCB(空气开关);3)110V供电对此类电机不稳定,推荐使用220V供电并加装过压保护器;4)应逐步喂料,过细筛网易致电机过载;5)若电机温度过高,应停机冷却。请发送机器运行视频;若电机已损坏,售后团队将跟进处理。
电机转向错误(反转)的原因与纠正方法??
电机旋转方向必须与设备匹配(通常为顺时针)。如需改变转向,打开电机接线盒,将内部铜连接片(铜条)按我方所发接线图旋转90°;请对照我方视频核对实际接线。转向错误将导致铡草机无法切割、自吸式粉碎机无吸力、碾米机滚筒异常运动。
电机漏电或接地不良的处理方法??
原文仅列出条目标题「电机漏电接地 · Motor electric leakage / earthing」,未提供具体问答内容。
I feel electricity on the machine. / There is no earth wire.
This is induced current when the machine is not earthed. Connect an earth (ground) wire from the machine body down into the ground. We can send a video showing how. Always earth the machine before use. If the earth wire is missing, a local wire can be used; tell us and our after-sales team will follow up.
中文:未接地产生感应电,用接地线连机身并入地。
The motor foot / cover / pulley is broken when we opened the carton.
Cast-iron parts can break if cartons are dropped or handled roughly during transport and re-transport. Please take photos of the outer carton and the damaged parts right away and send them with the quantity affected. Our after-sales team will follow up on replacement parts. Please ask your logistics partner to avoid rough handling.
中文:铸件运输跌落易断,开箱拍照(外箱+损坏件),售后跟进。
The pellet machine gives powder, no pellets.
Check the raw material moisture — it should be about 10-20%. If the material is too dry, add a little water (or a small amount of cooking oil). Check the die hole size (e.g. 4 mm / 6 mm) suits your material, and check the die holes are not blocked. Refer to the English manual; we can send an operation video.
中文:原料含水10-20%;太干加水或少量食用油;检查模孔大小和堵塞。
The die holes are blocked. / The machine jams after 30 seconds.
1) Always start the machine first, then feed material — never feed before starting.
2) Feed slowly, a little at a time.
3) Too much moisture or too fine powder blocks the die; too dry material can also jam.
4) Clear the blocked die before restarting.
Send us a video of operation if it continues.
中文:先开机后进料,少量多次;含水率过高或过干都会堵。
What oil should I use? / How much oil?
Use heavy-duty gear oil SAE 85W-90 GL-5 (machine gear oil, not engine oil) in the gearbox, and check the oil level with the dipstick. Oil quantity depends on the model (e.g. Model 250 takes about 20 L; Model 200 has no oil bath). For other gearboxes, EP90 gear oil filled to the marked hole. Please tell us your model to confirm.
中文:用 SAE 85W-90 GL-5 齿轮油(非发动机油),油量按型号。
> 待核实:用油口径有冲突(曾对客户说85W-90用发动机油也可),各型号油量待整理
The die has black dirt / looks like an old machine. / Where are the extra dies and rollers?
Every machine is test-run at the factory with grinding material, which leaves marks and residue on the die — this is normal; do not wipe it off. Extra dies, rollers and spare parts are packed in a separate box — please check all cartons against the packing list. The pellet mill has two power wires and no switch by design; connect with suitable copper cable to your switch.
中文:出厂测试留下痕迹属正常;备用模盘在单独箱里。
The flour is too fine. / Output is too low. / Screen keeps blocking.
On self-suction (claw-type) crushers, reduce the air damper / air flow, increase feeding, and clean the screen. Smaller screen holes = lower capacity: use 2-3 mm screens for higher output; very fine screens should only be used briefly as they overload the motor. Fibrous material slightly blocks the screen over time — shake it to clean. If capacity is still too low, the model may be too small (household type); ask us about a larger model.
中文:调小风门、增加进料、清筛网;筛网越细产量越低。
The crusher does not suck the grain. / Motor gets hot.
1) Check motor rotation direction — wrong direction stops suction (turn the copper links 90° to reverse).
2) Check the motor power and phase are suitable: a single-phase motor may be too weak for heavy materials; a three-phase motor is recommended where available.
3) Check the supply cable and voltage.
Send a video; our after-sales team will follow up if parts are needed.
中文:先查转向;单相电机功率不足可改三相;检查电线电压。
The rice roller moves back and forth. / How to assemble? / Bran comes out.
- Roller moving: remove the rice-mill shaft, tighten the lock nuts on both sides, reinstall; also check motor direction.
- Assembly: follow our assembly video; the big roller goes at the back.
- Switch hard to turn: replace following our video.
- Rice bran being blown out is normal, not a leak.
- Rice screens are wearing parts — order spares with the machine.
For combined rice mills we can send the electrical diagram (MCB, capacitors, forward/reverse switch).
中文:米辊窜动拧紧两侧锁紧螺母;大辊在后;吹出米糠属正常。
品牌名使用限制?
不能使用与已有客户相同的品牌名/商标;客户须自选品牌名,我方按约定将其印于铭牌、纸箱及激光切割件上。
The grinding stone broke. / Machine clogs. / Stone does not fit.
- Stone discs usually crack when the gap is adjusted too tight — do not over-tighten.
- Sesame and oily small seeds clog easily: feed a little at a time.
- Installing stone discs: remove the black plastic spacer (used only with metal discs) before fitting the stone.
- Noise: check that the fan blade is not touching the cover.
石盘到货破损怎么办??
石盘多因调太紧压碎;芝麻少量多次加;装石盘先取下黑色塑料垫。石盘到货破损:请发送照片;我方售后团队将跟进处理。
脱粒机玉米脱不净(籽粒留在玉米棒上)怎么办??
脱粒率难达100%,建议二次脱粒,避免过载。过载(喂入量过大)可能损坏内部零件。如发生破损,请发送照片和视频,我方售后团队将跟进处理。
吸粮机吸力弱、电机发热怎么办??
检查所有吸管接缝是否漏气并密封;吸管需正确倾斜插入粮食中。电机温升在约75°C以内属正常。如仍吸力弱,请发送视频。注:该问题仅基于单一案例,待核实。
汽油机/柴油机冒烟、无法启动、不锈钢搅拌机焊接维修相关问题?
冒烟通常由燃油质量差或化油器/开关调节不当引起;需添加机油并定期保养;燃油通过加油口加入。'汽油/柴油型'设备出厂默认不含发动机,除非客户下单时明确要求配装。不锈钢搅拌机可采用氩弧焊或CO2保护焊修复。如客户自行提供柴油发动机,请在生产前向我方提供其安装孔尺寸。
收货发现缺件(螺丝、轮子、链条、皮带轮、皮带等)或找不到备件怎么办??
请先检查单独标记的备件箱及密封小袋——备件均单独包装,且仓库有时会拆散托盘。请对照装箱单及装货照片清点纸箱数量。如仍缺件或发错件,请发送缺失部件清单及照片;我方售后团队将跟进处理(通常随下次订单补发,紧急小件则安排快递)。
货物运输途中破损(外箱破损、零件损坏)怎么办??
收货时请立即拍摄集装箱/外箱及破损零件照片,注明数量,并连同承运人/货代出具的破损报告一并发送给我方。拼箱货(LCL)中转次数多,破损概率更高;我方采用托盘加固及电机全泡沫包装以降低风险,同时建议购买货运保险。我方售后团队将在审核照片后跟进处理。
收款账户说明?
公司银行账户信息显示在销售团队开具的形式发票(PI)底部,受益人为湖南维燕机械科技有限公司(Hunan Weiyan Machinery Technology Co., Ltd.)。请从贵司公司账户付款,并在付款后将银行水单发送给我方。
付款条款:定金与尾款支付方式?
公司政策:30% T/T 定金;生产在定金到账后启动。余款凭提单(B/L)复印件付清,全款到账后电放提单(telex release)。不接受到港后付款。小订单需一次性付清100%货款。
价格条款:FOB / EXW / FCA / CIF / DDP?
整柜订单通常报 FOB 深圳(蛇口),FOB 价格不含海运费;零售数量报工厂价(EXW)或送至客户指定的中国货代仓库(FCA);一般不报 CIF 或 DDP —— 请客户自行向其货代询价海运至目的港费用。
包装方式:纸箱 vs 木箱?
铡草机采用高强度7层瓦楞纸箱包装,电机上下均用聚氨酯泡沫(polyfoam)全包裹,兼顾运输安全与体积控制以节省运费;木箱包装可选,但需额外收费。颗粒机采用木箱包装,内衬泡沫。纸箱可按客户海关要求标注内容物及箱号。
生产周期(整柜订单)?
整柜铡草机常规生产周期为收到定金后约28–30天;旺季及春节、五一、国庆节前可能延长至35–40天;新品开发及复杂定制所需时间更长。确切装柜日期由销售团队在订单确认后通知。
排产与订舱流程?
生产按定金到账时间先后安排;装柜还需客户提供货代出具的装运单(SO),谁先提供SO并确认装柜时间,即优先安排;请客户提前约一周提供中国货代联系人;我方收到SO后约4–5天内完成订车及装柜;旺季请尽早订舱。
小单/现货交期?
小批量零售订单(1–10套):如有现货,付款后约7–10天内打包并交付至客户指定的中国货代仓库(有时更快);若无库存,生产周期约10–15天;柴油动力颗粒机因需单独采购发动机,生产周期约25–30天。
春节前下单注意事项?
春节前工厂订单密集,物流通常于2月初停止运转。建议客户至少提前一个月下单,以确保货物能在假期前出运。单台样机可能安排在节后生产。
第三方及私人账户付款限制?
不接受第三方公司或个人代付。银行监管要求付款人须与进口商一致;第三方付款需提供关系证明,且易触发反洗钱审查及账户冻结风险。我方不接收任何私人账户付款。
粉碎机 9ZF-50?
9ZF-50 grinds grain and also straw/corn cob; uses 3kW copper motor. 中文:9ZF-50 可磨粮食,也可磨秸秆/玉米芯,3kW 铜电机。
质保政策?
一般不提供正式质保,因机器单价较低,国际运费常高于机器本身价值,跨境退换修不具实操性。我们提供:出厂前测试及验货视频、终身视频/WhatsApp技术指导、操作说明书、配件供应;并建议客户随机器一并订购常用易损件(刀片、筛网、皮带等)。电机唯一易损件为启动电容,建议随机备货;电机热保护功能可应要求写入PI。
我司一般不提供正式质保,因机器单价较低,国际运费常高于机器本身价值,跨境退换修不具实操性。替代方案包括:出厂前测试及验货视频、终身视频/WhatsApp技术支持、操作说明书、备件供应;并建议易损件(刀片、筛网、皮带等)随机一起订购。如遇问题,请发送照片和视频,售后团队将提供技术指导。
第8页
> 待核实:已按老板口径改为:一般不提供质保
出口单证要求?
提供 Commercial Invoice (CI)、Packing List (PL,含每项毛重/净重)、提单(B/L)副本、电放(telex release)、原产地证(Certificate of Origin, CO),以及按需提供的保险单;所有单据可按客户目的国海关格式要求制作(如PDF格式、发票标题、HS编码、装箱单/提单上的品名描述、技术参数通过电子目录提供)。
出口单证包括形式发票(PI)、商业发票(CI)、装箱单(PL)、提单(BL)和原产地证(CO)。CI与PL须列明每项货物的毛重/净重;CI、PL、BL、CO信息须一致。提单:我方先发送BL草稿供您确认(收货人、通知人、品名、HS编码、运费预付/到付);BL签发后修改将收取改单费;尾款付清后办理电放(Telex Release)。原产地证(CO):可提供(CCPIT版或海关版,适用时含FORM E);需政府审批,节假日前后请预留办理时间。
申报金额规定?
商业发票(CI)上的申报金额必须与实际收款金额一致;海关查验严格,不得低报。提单(B/L)上的品名可概括描述(例如“CHAFF CUTTER SETS”“spare parts”),发票上的品名描述可按客户所在国海关用语要求调整,但须确保准确。
贸易术语说明?
主做 FOB 深圳(盐田/蛇口):我方安排拖车、装货、港口操作及出口清关;客户货代订舱。EXW(工厂交货价):不含内陆运费、港杂费及目的港清关,但出口报关仍以我司名义进行。CFR/CIF:应客户要求提供(如客户银行或信用证要求),运费在报价时与货代确认。宁波、广州、青岛等其他港口出运为个案处理。通常同时报工厂价(EXW)、FOB深圳、CFR/CIF三种价格。
报价所需信息?
正式报价由销售团队出具,价格取决于型号、电机/发动机选项、数量、包装、贸易术语及实时汇率。请提供:型号、数量、目的港、电压/相数/频率(如220V 50Hz单相)、动力类型(电动机/柴油/汽油)、品牌及包装特殊要求。可报工厂价(EXW)、FOB深圳、CFR/CIF;美元报价可能随美元兑人民币汇率变动而调整。
标准付款条款(30/70)?
标准条款:30%定金通过T/T到账后启动生产;70%尾款凭提单副本(BL copy,扫描件)支付;尾款到账后1个工作日内安排电放。生产及原材料采购仅在定金到账后启动。
尾款支付与单证释放规则?
未付清尾款前,不释放正本单据及电放;不提供账期(如货到后30天付款)或目的港到货后付款。
新客户首单尾款支付方式?
新客户首单尾款通常在发货前付清:货物备妥后,我方发送成品机器及装柜照片/视频供客户验货,客户确认后支付尾款,我方即安排发货。复购订单适用标准条款(30%定金+凭提单副本付尾款)。小订单及样品一般要求全款预付;样品订单偶见50%定金+发货前付尾款。
银行转账费用与到账时间?
T/T银行手续费由买方承担;请确保发票全额到账(中转行扣费导致的短付由买方补足)。付款后请发送SWIFT水单(MT103)。美元T/T通常2–3个工作日到账;经第三方或代理付款可能需7–10个工作日。建议一次性汇款而非分批,以节省手续费。付款金额须与商业发票一致;尾款须从买方公司账户支付。
信用证及其他付款方式?
首选T/T付款。首次合作不接受全额信用证(L/C);L/C at sight仅个案接受(如T/T困难的市场),有时需配合T/T定金;L/C条款须逐条审核(受益人名称/地址、品名拼写、数量、保险等)。小订单可通过阿里巴巴Trade Assurance或付款链接支付(链接3天内有效)。其他渠道(如人民币转账)须遵循我司财务部规定,请联系销售对接人。
收款账户防诈骗提示?
我司银行账户信息仅以正式形式发票(Proforma Invoice, PI)所载为准;绝不会通过聊天消息变更收款账户。如收到任何要求支付至新账户或不同账户的消息,请勿付款,须通过第二渠道(视频通话/官方邮箱)向我方核实。我司美元及人民币账户均列于PI上;PI所载SWIFT代码为唯一有效依据。
定制品牌纸箱与唛头?
- 定制印刷纸箱(含客户品牌LOGO):每型号起订量100台;不足100台则使用中性纸箱+客户品牌标签;
- 客户品牌标签/贴纸可固定于机器本体(螺丝或薄膜方式);
- 唛头内容可含收货人、地址、“Made in China”、箱号;拼箱货(LCL)需印客户货代录入号;
- 唛头图稿由客户确认后印刷;定制印刷纸箱需额外生产时间(约25天)。
第7–8页
稻麦脱粒机?
稻麦脱粒机:产能约1000kg/h。原文只给出产能,未列出配套动力、型号、重量、包装和可选配置信息。
交货期(生产与发货时间)?
交货期自收到定金起计算:库存机器约3-5天;小型定制订单约5-10天;小型批次切草机约10-12天;整柜订单通常15-25天(40HQ约22-26天);紧急订单有时可缩短;旺季(尤其是春节前)为30-45天;定制印刷纸箱增加约25天;特殊电机(如220V/60Hz单相)也会延长交期。每单确切交货日期由我司销售团队确认。中文摘要:库存3-5天;整柜常规15-25天;旺季30-45天;定制纸箱/特殊电机会延长。
节假日与旺季安排?
中国新年:工厂放假约两周(通常在1月下旬至2月,每年日期不同);国内物流自2月初暂停;春节前一个月为旺季,如需节前出货,建议11月中旬前下单、12月10日左右完成装运。劳动节(5月1–5日)、国庆节(10月1–7日)、元旦(1月1–3日):银行关闭,付款及电放无法处理,请提前约一周付款。国庆节前集装箱舱位紧张,请尽早订舱。
订舱与船期配合要求?
我方将在货物备妥前约一周通知买方,以便其货代订舱;我方需在截关日前7–8天收到装运单(SO,即订舱确认),方可安排拖车与装货;装货仅在收到SO后安排;若未按时订舱,将导致装货及交货延误;船舶通常在装货后约10天离港;船公司可能调整截关日期,且年底/月底舱位紧张,请尽早订舱。
集装箱规格与载重限制?
20GP:内径约5.69 × 2.13 × 2.18 m;实际装载体积约27–28 CBM;载重约17–18吨。40HQ:内径约11.8 × 2.13 × 2.72 m;计划按约65 CBM(理论值68 CBM);载重通常控制在约26–28吨,视船公司及航线而定。理论容积不等于实际装载量(受纸箱、木箱、托盘影响);每票货物装柜前均称重。切草机较重,40HQ常因重量满载而未达体积上限;颗粒机、粉碎机等轻货可搭配填充空间。
各型号集装箱装柜参考数量?
装柜数量依具体型号及是否含电机而定,仅为参考:切草机(含电机):20GP约95–225台;40HQ约300–420台(例如型号2000在40HQ中约338–340套);碾米机:小型号约360套/40HQ;锤片粉碎机/磨粉机:约180–200套/20GP;颗粒机150/160:木箱包装下单台约0.2 CBM,常用于填柜。请提供具体型号与数量,我司销售团队将为您核算精确装柜方案。
出运港口?
主出运港:深圳(盐田/蛇口/大铲湾)。我司工厂位于湖南,距深圳约650–700 km。其他港口(如宁波、广州、青岛、义乌拼箱)可应要求安排,但内陆运费可能更高。中亚方向:可通过新疆伊尔克什坦/乌恰陆运至塔什干。
运费如何计算??
海运费波动频繁,我司在报价时向货代实时询价,并由销售团队在正式CFR/CIF报价中列明。请提供:目的港、集装箱类型或总数量、具体型号、是否在中国已有自己的货代。空运或快递需提供包装后尺寸与毛重。若您有中国境内货代,我司可报FOB/EXW价并送货至其仓库。
拼箱(LCL)发货操作流程?
小批量订单可送至您指定的中国境内货代仓库(如深圳、广州、佛山、义乌等)。请提供货代仓库地址、入仓编号(warehouse entry number)及唛头(shipping mark / customer code)。我方将每箱标注入仓编号/唛头,发货前拍照留存,并发送追踪号。入仓单(warehouse receipt)为交货凭证,我方将转发给您。注意:LCL仓库不接受电池、液体、油类、粉末等物品;重货须打托。
货运保险与单证提供?
提供形式发票(PI)、商业发票(CI)、装箱单(PL)、提单(BL)、产地证(CO);提单先发草稿供确认;建议买货运险以防损坏或延误。
第7页
目的国特殊单证要求?
各国进口单证要求如下:
- 埃及:需ACID编号及CargoX平台上传(发票、装箱单、原产地证、提单),并提供海关版原产地证(CO);
- 印度:通常要求运费预付(Freight Prepaid)及主单(Master BL,非分单House BL);需提供IEC、PAN、GST信息;如需,纸箱须贴MRP价签及进口商标签;
- 秘鲁/拉美:提单首页须注明产品名称及对应HS编码;
- 沙特阿拉伯SABER、肯尼亚COC可安排办理,费用承担方逐单约定;
- 波兰/欧盟:可签署关于俄罗斯/白俄罗斯出口限制的出口声明。
请在发货前告知贵国具体单证要求。
第7页
HS编码?
我司出口申报使用真实HS编码及实际成交价值,目的国进口商须自行确认当地归类:
- 铡草机/饲草饲料加工机械(含颗粒机):8436100000(843610);
- 铡草机/颗粒机配件:84369900;
- 粮食磨粉机/面粉机:8437800000;
- 皮带输送机:8428399090。
第7页
> 待核实:配件HS编码有一处记为84369000,按多数记录取84369900
单证与实物标签一致性?
为避免目的港海关查验及清关延误,机器铭牌型号、纸箱标签型号、运输单据(CI/PL/BL)所载型号必须完全一致。每只纸箱标注主产品名称及箱号(如1/220),与装箱单匹配。我司按实际出运货物(含电机)如实申报,重量准确。请提前告知贵国海关对标签的特殊要求。
第7页
出货前加单与改单政策?
已喷漆及已向海关申报的货物不可更改;同型号产品为整批生产,跨型号变更受限;若集装箱已满,最多可加约10台或2CBM;如需加货更多,建议更换更大尺寸集装箱并补交相应定金。
包装方式?
- 铡草机:7层加厚纸箱+双向打带;主机、输送机/料斗、电机分装(通常每套3个纸箱);
- 电动机:单独纸箱内全泡沫包裹;
- 颗粒机:木箱包装(含电机,一机一箱);
- 木箱材质为胶合板(免熏蒸);其他机型木箱包装可选,需额外收费;
- 拼箱货(LCL)/重货:打托盘;电机绝不置于托盘底部;
- 备件及螺丝单独装入标有“spare parts”的专用箱或密封袋。
第7页
> 待核实:拼箱是否用木箱存在冲突说法(易压坏电机 vs 防变形),未写定论
易损件与备件供应?
易损件(刀片、大米筛、筛网、皮带、皮带轮、齿轮、模具板等)建议随整机一同下单——集装箱内随货发出的备件成本远低于后续空运或快递补寄。请在生产前告知所需数量。备件单独装入标有“spare parts”的专用箱;到货时请检查该箱。
第8页
产品认证?
- 铡草机与颗粒机:具备CE证书;
- 目的国认证(如沙特SABER、肯尼亚COC)可配合办理,费用承担方逐单约定;
- 如需政府检测,我司可提供设备技术参数。
请在下单前告知目标市场所需认证。
第8页
> 待核实:BIS说法'没被要求过但有证'不清,未写
各市场电压与频率配置?
电机按客户所在地电源规格配置,下单时须确认电压、相数、频率:
- 印度:单相220V/50Hz(三相440V);
- 埃及:220V/50Hz;
- 非洲地区:多为380V或220V/50Hz;
- 菲律宾:220V/60Hz(需特制电机,交期更长);
- 秘鲁/拉美:220V/60Hz;110V电机易烧毁,推荐220V;
- 巴西:380V/60Hz(单相220V/60Hz)。
颗粒机:KL180为最大单相型号;KL210及以上必须三相。
第8页
电机接线、插头与转向?
- 功率约2.2 kW以上电机不应使用家用插头,须直接接入空气开关(MCB);插头可应要求加装(请在订舱前告知);
- 电机旋转方向须与机器匹配(我司多数机器为顺时针旋转);可通过端子盒内铜连接片旋转90°调整转向;
- 标准电机转速为2800–2880 rpm;若使用1440 rpm电机,则需更换皮带轮;
- 供电电缆截面积须足够(≥2.5 mm²)。
第8–9页
机器颜色?
标准色为红+灰,为最畅销配色;浅蓝色或深蓝色可按需定制;亮黄色不推荐,因易显脏。请在生产前确认颜色。
第9页
> 待核实:仅一处出处
付款与交货安全政策?
客户可通过验证公司文件、实地参观或视频看厂建立信任;生产在收到定金后启动;尾款支付方式为凭提单(B/L)复印件支付,即货物已装运完毕后才收取尾款;零售订单统一发往客户指定的中国境内货代,并提供发货照片及签收凭证;对新合作伙伴建议先下试订单。
Neutral packing / no brand / custom nameplate?
可发货不带任何品牌;可在铭牌上印制客户自定义型号编号。
中性包装与定制铭牌政策?
可做无品牌/中性箱/特殊铭牌,下单时确认;中性纸箱需提前通知;中性包装中,纸箱上贴型号标签以区分型号;样品和小批量(如2台样品或约10台)一般不定制。
What is your best price? / Other suppliers are cheaper, can you reduce? / Give me your final price.
Our quotation is our ex-factory price, kept the same for new and old customers; it depends on model, configuration and quantity. Price differences between suppliers usually come from configuration (blade thickness, motor material and real power, frame and gear material, packing). For an exact or revised offer, our sales team will send a formal quotation — please tell us the model, quantity, destination port, voltage, and which item you feel is high and your target price.
中文:报价对新老客户一致,按型号/配置/数量;具体价格由业务员正式报价。
How much is this machine? / Send me price list. / Please quote.
Prices are given in a formal quotation by our sales team. Please share: model(s), quantity per model, voltage/phase (or petrol/diesel engine), branding or color needs, destination port/country and whether you have a forwarder in China. The quotation lists each model with specifications, and the total CBM/weight for container planning.
中文:价格由业务员单独报价,请提供型号、数量、电压、定制需求、目的港、中国货代情况。
Why is the USD price different from last time? / Why did you increase price?
Our factory prices are set in RMB. The USD price is converted at the exchange rate at the time of quotation, so when the RMB/USD rate or raw material cost (e.g. copper) changes, the USD figure can change even if the RMB price did not. For the current USD price, our sales team will send an updated formal quotation; please share model, quantity, destination port and voltage.
中文:以人民币定价,美元价按报价时汇率换算,汇率/铜价变化会导致美元价变化;具体由业务员重新报价。
MOQ and sample order?
常规 MOQ 5 台;1–2 台按零售价,需中国货代,送到货代仓库;样品价统一。设计更改 / 定制需至少每型号 5 台。样品报价需提供型号、数量、电压及中国货代仓库所在城市。
Can I mix several models in one container?
Yes, mixing is possible, but each model needs at least 5 sets (1 set per model is not accepted because production becomes complicated). For a 20ft container we normally accept about 5–6 different models. We will calculate the total CBM and weight of your mix and send a loading list.
中文:可混装,每型号至少 5 台,20 尺一般 5–6 个型号。
FOB Ningbo / Guangzhou / other ports?
主港深圳,也可广州;宁波/义乌等可做但国内段运费另算。需提供首选港口及数量以便业务员报价。
OEM / private label branding?
可做铭牌、纸箱唛头、皮带罩激光切割,另可贴品牌贴纸、英文警示贴、电机印 logo。定制在下单时确认;零售/极小批量通常不支持定制。
Custom carton MOQ?
定制印刷纸箱一般每型号 100 套(纸箱供应商要求);不足则用中性箱+贴标;新纸箱设计涉及纸箱供应商的设计/制版费。
Laser-cut logo limits?
激光只能切简单品牌名(约 11 字以内),复杂图案或长词会切坏;混合机/木材粉碎机不可激光切割,改用高质量贴标;刀片上一般不提供刻字,仅特殊情况下允许极短词。
颜色定制政策?
可按色卡定制颜色(常规色:红、灰、橙、蓝、绿);因粉末喷涂线换色会产生浪费,小订单使用产线当日颜色(多为红+灰);每单颜色数量有限;喷漆完成后颜色不可更改;不锈钢部件不可喷红色。
彩盒与金色螺丝政策?
彩盒(印刷礼盒)MOQ极大,不提供;螺丝仅提供银色,不提供金色螺丝。
加急订单政策?
加急生产仅在预付全款且所有细节(型号、颜色、纸箱设计、品牌)于同日确认的前提下可能实现;新品及复杂定制会拉长排期;具体可行性需销售团队核实当前工厂产能。
海运费报价规则?
我方报价为FOB深圳;海运费由买家自行委托货代报价并承担,因运费随时间、航线、季节浮动;我方仅提供参考;我方支付FOB段费用至中国货代,买家支付海运段费用;如需运费参考,请提供目的港、集装箱尺寸或数量及具体型号;小批量出货运费取决于总数量。
国内集货仓配送政策?
可配送至客户指定的中国境内货代仓库(如义乌/广州/佛山);广州通常比义乌运费更低;国内段运费按目的地及数量单独核算并报价。
集装箱装柜数量说明?
铡草机属重货小体积产品,40HQ通常先达重量上限(约27.5–28吨)而非空间上限;仅装铡草机时,20ft常更经济,或可混装轻货;具体装柜数量依型号而定,并受是否含电机/发动机及备件影响;我方出货前提供含总CBM与总重量的装柜明细。
电机可连续运行多长时间??
不建议电机长时间连续运行,应每4–6小时停机休息一次。长期使用后最常见的电机故障是启动电容损坏,该部件易于更换。
付款方式政策?
整柜订单请以美元通过T/T从海外公司账户支付(出口报关所需);小订单可通过阿里巴巴支付链接付款(平台服务费由买方承担);或由中国代理以人民币支付至我司账户;不接受印度卢比(INR)付款。
信用证(L/C)接受政策?
首单建议采用T/T作为试单;合作顺畅后,L/C可个案讨论,须经我方销售团队确认;L/C订单所需单据为商业发票、装箱单(含重量与尺寸)、提单(B/L)及原产地证;正本单据银行间交接,扫描件同步发送客户。
电机是否为纯铜?是否为真实3HP功率??
所有铡草机电机均为全新材料制造的纯铜线电机,不含再生材料;电机是核心部件;我方3HP电机出厂前逐台测试,实测功率不低于2.2KW;低电压或电压不稳叠加电机功率不足易导致堵转,因此我方强调真实功率输出。
How can I know the motor is copper?
A 2.2KW copper motor weighs about 23kg; a much lighter one usually means aluminum wire or old material. You can also peel the wire insulation: golden is copper, silver is aluminum. Our motors use machine winding for compact, stable coils. We can send photos of the winding and cable connection.
中文:2.2KW 铜电机约 23kg,剥线金色为铜、银色为铝;可发绕组照片。
Are all your motors copper?
Chaff cutter motors are copper. Exceptions: the small 0.95KW corn thresher and the small vegetable chopper use aluminum motors. Please check the motor specification in the quotation for each model.
中文:小型玉米脱粒机(0.95KW)和小型蔬菜切碎机用铝电机。
Can you supply a 5.5KW single-phase motor?
Real single-phase motors reach about 3.2–3.5KW maximum. A single-phase "4KW" is actually about 3.3–3.5KW, and a 5.5KW single-phase motor is not realistic. For higher power, a three-phase motor (380V or your local three-phase voltage) is required.
中文:单相真实最大约 3.2–3.5KW,更大功率必须三相。
Is this diesel engine really 14HP/16HP?
We tell the actual power. In the Chinese market engine nameplates are often overstated: for example, a 192F diesel engine marketed as 14–16HP is actually about 11–12HP. We match engines to machines by actual power.
中文:市场发动机常虚标,192F 标 14–16HP 实际约 11–12HP,我们按实际功率匹配。
Can you make 440V three-phase or 220V/60Hz motors?
Our standard motor is single-phase 220V/50Hz (China three-phase is 380V). Other voltages/frequencies such as 440V three-phase, 220V/60Hz or 110V need special production, cost a bit more and take about 10 extra days; some special motors need a minimum quantity. 110V/60Hz in small quantity may not be accepted by the motor factory. For high-power machines we suggest three-phase.
中文:标准单相 220V/50Hz;440V、60Hz、110V 需特制,价稍高、多约 10 天,部分有 MOQ。
Can you supply 1440rpm or 950W/1500W motors?
1440rpm, 950W and 1500W motors are not offered for these machines. For threshers the motor must be at least 1.8KW. Three-phase motors converted to single-phase need a capacitor.
中文:不做 1440rpm/950W/1500W 电机;脱粒机至少 1.8KW。
Does the motor come with a plug? / What cable is supplied?
We don't suggest a plug. The motor comes with about 1.3–1.5m thick cable; please connect it to an MCB (air switch). A plug with long thin cable causes low voltage and may stall or burn the motor. For machines above 2.2kW (e.g. pellet mills), starting current is 40–50A while a normal socket is max 20A, so use a wall MCB (about 32–60A). A larger plug with 3 wires (including earth) can be fitted on request.
中文:不建议带插头,配 1.3–1.5m 粗线接空开;2.2kW 以上接墙上 32–60A 空开。
Can you install an MCB or forward/reverse switch on the machine?
Yes, an MCB (installed on the frame) and a forward/reverse switch are available as options at extra cost, shown in the formal quotation. Note the reverse switch only works in the specified direction, so wiring must follow the diagram. For pellet mills we do not suggest mounting an MCB or plug on the machine because dust and vibration damage it.
中文:可加空开、正反转开关(另计费);颗粒机不建议机身装空开/插头。
Can the chaff cutter run with a petrol or diesel engine?
Yes. Side-frame models can use an electric motor, petrol engine or diesel engine, with the pulley and belt changed. The petrol frame is a special frame with MOQ 10 sets. Petrol engines are cheaper but weaker; diesel engines are stronger and more expensive. We suggest petrol engines for chaff cutters and diesel engines for pellet mills. Some sample models are not offered with engines.
中文:侧架款可配电机/汽油机/柴油机(换皮带轮皮带),汽油机架 MOQ 10 套;铡草机推荐汽油机,颗粒机推荐柴油机。
Can I use my own engine with your machine?
Yes. Please send the engine's base mounting hole dimensions (4 holes). Each engine factory's design differs, so the belt can only be matched correctly after testing with the engine. Machine and engine power must match — a big machine with a small engine, or a small machine with an oversized engine, will shorten service life.
中文:提供发动机底座四孔尺寸;皮带需实机测试匹配;功率须匹配否则缩短寿命。
Do you ship the battery with the electric-start diesel engine?
Batteries cannot be exported by sea from China (customs restriction), so we ship only the battery bracket; please buy the battery locally. Electric-start diesel engines cost more than hand-start ones.
中文:电池不能出口,只发电池架,请当地购买。
切碎机适用物料范围?
可切鲜草、干草、秸秆、细甘蔗、玉米秆、小玉米棒;软干料可以,但最适合鲜草;非常粗硬物料不适用;一次喂入量不宜过多(约4–5根硬茎);最大枝条直径约3cm;更粗枝条需用专用枝条粉碎机;带方形进料斗的型号还可处理南瓜、土豆、瓜类。
切碎长度是否可调?哪些型号支持??
仅齿轮款(gear models)支持切碎长度调节,调节范围约0.5–1cm(短切)或3–5cm(长切);无齿轮型号不可调,拆除刀片亦不能改变切碎长度;例如FC-800(无齿轮)不可调,FC-800G(带齿轮)可调。
是否可改装5刀以实现更短切碎??
齿轮款可升级为5刀(需额外付费);非齿轮款不可升级,因机身需加高;5刀可使切碎略短;直刃刀片会增加电机负荷;请向销售团队确认具体型号是否支持。
是否可提供加厚/加重机架??
可提供加重/加厚版本,但会增加成本,价格需单独报价;请告知所需型号及数量。
颗粒机可加工哪些原料?是否需要胶水或蒸汽??
无需胶水或蒸汽;可用玉米+草、玉米+麸皮、米糠+少量草等混合料;水分需适中:过干易成粉,过湿易堵模;若混合料过干,可添加少量食用油或粘性更强的物料(如麸皮、碎玉米);本公司不生产鱼饲料或生物质颗粒机。
颗粒机模盘孔径如何选择?随机配几个模盘??
常用模盘孔径:2.5mm适用于雏鸡/雏鸭,4mm(最畅销)适用于鸡/鸭/猪仔,6mm适用于猪/羊/马;8mm在部分型号上可选;每台机器随机配1个4mm模盘;其他孔径为可选配件,建议与主机一并发货以节省运费。
颗粒机如何加油及启动操作??
齿轮油加至油尺下三分之一处;严禁加水;先启动机器并使其正常运转,再均匀进料;请严格遵循说明书操作。
差速款颗粒机与后轮式颗粒机的区别??
差速款采用封闭式传动结构,无油封位置,体积更大、重量更重、更耐用,且降低电机负载;后轮式传动轴外露,必须配备油封;目前我司仅供应差速款颗粒机。
标称产能是否真实?实际产能如何??
我司产能标注偏保守,避免客户失望;例如标称800kg/h的机器实际产能约1吨/h;其他参考值:6N70碾米机500–600kg/h,家用型180–250kg/h;粉碎机产能取决于筛网孔径和滚筒长度(0.6mm筛网时约100–150kg/h);各型号具体参数见报价单。
如何获取设备尺寸、重量、CBM等规格参数??
报价单中逐型号列明产能、功率、外形尺寸、整机重量及包装尺寸,并在表末汇总总CBM,便于客户规划集装箱装载;请告知所需型号,我们将提供对应报价单。
蔬菜切片机材质及切片厚度能力??
蔬菜切片机与碾米机采用201不锈钢;窗式蔬菜切片机型号20采用304不锈钢;标准切片厚度3mm,标准切丁尺寸15mm立方;最薄可切约2mm;不建议更改刀片规格;农业类粉碎机不推荐用于食品加工。
芝麻、花生酱能否用我司研磨机加工??
型号150需加水运行,不适用于干磨;型号160支持干磨:芝麻效果良好,花生效果较弱;需小量多次进料;研磨机盖体结构不可改为铝制;塑料部件为食品级耐磨材质。
是否有工作视频、装配视频或说明书??
有目录PDF、工作视频、装配视频(含整机、皮带调整、链条、电机装配、换挡杆、刀片调整)、白底照片和英文说明书(安装图见第5–6页)。视频不带公司名称。部分型号仅有操作手册。下单后我们会为您拍摄带品牌标识的机器测试视频。若WhatsApp传输失败,可通过阿里巴巴或微信发送。
能否现在发送切鲜草的视频??
冬季(约10月至次年4月)中国无鲜草,因此切鲜草视频只能在每年5月至9月拍摄;其余月份可提供使用其他物料的运行/测试视频。
谁来协助我安装机器??
我们提供在线安装支持(视频+文字),并附有装配视频和说明书。如遇问题,请发送现场照片或视频,我们将远程指导。
是否销售备件?机器随机配哪些部件??
每台机器随机配一套原厂部件。备件可单独订购——建议与主机同柜发货(装入箱内),以节省运费;单独快递寄送成本较高。备件须与机型匹配。粉碎机筛网仅有两种尺寸:100×760mm 和 100×860mm,不接受其他尺寸定制。建议随订单同步采购约10%易损件作为库存。备件按体积(CBM)计,装柜数量需相应调整。
电机不转/卡停/转速慢/过热,如何排查??
每台电机出厂前均经测试。请检查:电压必须为220V(最低不低于210V);电缆截面积至少2.5mm²,距离电源越远则需越粗;不可一次性投入过多硬质秸秆(建议每次4–5根)。若皮带运转极慢,说明电压偏低。对于反转开关,请检查接线方向。请发送现场视频以便我们进一步判断。
新机器噪音大、电流高,是否正常??
新机初期噪音大、电流高属正常现象。请先加注齿轮油;经过磨合期后,噪音与电流会明显下降。如持续异常,请发送视频供我们核查。
吸粮机吸力不足/电机发热,如何处理??
电机温度达约75°C以内属正常;连续工作2–3小时后需停机休息。吸管应保持倾斜并尽量贴近粮食表面。吸力不足常见原因包括:电机转向错误、转速偏低、风扇叶片损坏、内部堵塞或管道接头漏气。
运输中带轮或电机盖开裂,如何处理??
带轮与电机盖为铸铁材质,运输中跌落易致开裂。我们随单配发备用带轮和电机盖,并采用最厚聚氨酯泡沫保护电机。大齿轮为球墨铸铁材质;砂型铸造外观可能略呈凸起状,但不影响使用。请提供开裂部位照片,我们将核查处理。
到货缺件,如何处理??
我们将首先核查;如确属我方漏发,将在您下一批订单中免费补发缺失部件。我们已加强包装管控(螺丝密封袋装、纸箱逐箱装箱检验)。请注意:同一批次的主机箱与皮带箱须成套销售——部分部件(如导流板)装于皮带箱内,拆分批次销售易被误判为缺件。
触摸机器有触电感,是否漏电??
此为感应电流,非真正漏电。请按说明书要求连接地线:电机内部有接地标识;用导线将机身固定螺钉与大地可靠连接。说明书明确注明接地由客户自行完成。新订单可额外增加第三根(接地)线。
颗粒机不出粒/出粉/模具堵塞,如何处理??
通常因物料水分过高或过低,或纤维含量过高所致。请调整水分,并添加粘性辅料(如麸皮、碎玉米)。开机后先空载运行至正常状态,再开始进料。若模具堵塞,需清理或更换模具。详见说明书第5页‘故障与排除’章节。
新颗粒机内有黑色残留物,是否为二手或脏污??
黑色残留物为出厂前试机研磨物料(如木屑、谷壳等)残留,属正常现象,非二手或污染。使用前请按说明书清洗模具及腔体。
There is black dirty material inside — is this a used machine?
No. The black material is grinding material used during factory testing to polish the die and rollers. It is not a used machine; please don't try to remove it.
中文:黑色物质为出厂测试用研磨料,用于抛光模盘和辊轮,不是二手机。
The machine doesn't cut well. How do I adjust the blades?
Blades are adjusted one by one by our technician before delivery; please don't change the blade position unnecessarily. Test with a piece of paper — the moving blade must be close to the fixed blade. Assembly/blade adjustment videos are available.
中文:出厂已逐把调刀,勿随意调;用纸测试,动刀须贴近定刀。
Do you test every machine? / Can I inspect before shipment?
Chaff cutter motors are tested with material before delivery, and blades are adjusted one by one. You are welcome to inspect at the factory, and online (video) factory inspection is also acceptable. Special on-site testing of mature models (e.g. running with engines/diesel) involves extra cost, please discuss with our sales team.
中文:铡草机电机出厂物料测试;欢迎到厂验货,也接受在线验厂。
What is the HS code for the chaff cutter?
Chaff cutters are generally classified under heading 8433 or 8436 (e.g. 8436.10), but the final HS code depends on your country's customs — please confirm with your customs broker; we will use the code you require on the documents. The motor is declared together with the machine, not separately.
中文:铡草机一般归 8433/8436,以进口国海关为准,按客户要求填写。
Do you have CE certificate? / SASO?
Our company holds ISO 9001 quality management certification. Chaff cutters and pellet mills have CE certificates, which we can send. Motors have China 3C certification but no SASO; SASO or other certificates can be arranged if the buyer covers the certification cost. Petrol engines exported to the USA need EPA certification. Please ask our sales team for the certificate of a specific model.
中文:公司有 ISO 9001 质量管理体系认证;铡草机、颗粒机有 CE;电机有 3C 无 SASO,客户出费可代办;出口美国汽油机需 EPA。
Can you ship 1–2 sets directly to my country? / Do I need an agent?
Do you have an agent in China to arrange shipping? For retail quantities we deliver the machines to your forwarder's warehouse in China (e.g. Guangzhou, Yiwu, Foshan, Shenzhen); we handle China-side delivery and export, and your agent handles shipping and destination customs. We do not ship retail quantities directly overseas.
中文:零售量送到客户中国货代仓库,不直发海外。
Can I be your exclusive distributor?
We will not actively sell to other customers in your area, and our sales team will try to get exclusivity approval from our boss. Final exclusivity is decided by the company management.
中文:承诺不主动卖给同地区其他客户,独家需老板批准。
Can I load goods from other suppliers in the same container?
Yes, but we must first calculate total CBM and weight. Goods from other suppliers must be delivered to our factory first; each company declares its own goods, each side bears its own local costs, and we charge a small loading/FOB fee. Sometimes shipping the other goods LCL from their nearest port is cheaper — we will help you compare.
中文:可以拼柜,先算 CBM 和重量,其他供应商的货先送我厂,各自报关,我厂收少量装柜费。
Do you have rice mills, crushers, feed lines or other machines?
Yes, we are a manufacturer and exporter and supply a complete range, including rice mills, crushers and small feed lines, for one-stop supply in one shipment. Not available: fish-feed pellet mills, biomass pellet mills, turmeric grinders, sugarcane machines, sugar/catering grinders. New products need a prototype first; we don't suggest buying immature technology.
中文:产品齐全,碾米机、粉碎机、小型饲料线等可一站式供货;不做鱼饲料、生物质颗粒机等。
Chaff cutter with grinder combo 9ZT-9NT21?
Larger 9ZT-9NT21 combo: about 2.5 t/h; 4kW copper motor. 原文备注:与宣传册参数核对。
Mini grass chaff cutter?
Mini grass chaff cutter: 0.55kW copper motor; about 18kg with motor; packing 790×430×425mm (0.146 CBM). 原文备注:与宣传册参数核对。
小型铡草机 9ZT-0.4?
外观与结构:小型铡草机,用于切碎牧草、玉米秸秆等饲料;标配铜线单相电机驱动,也可选配汽油机或柴油机;含切割系统(4动刀+1定刀)及进料口结构。
图上标注:型号:9ZT-0.4;电机:2.2kW (3HP),220V/50Hz,约2800rpm;产能:0.4–1.0 t/h(干草约0.4 t/h,玉米秸秆约1.0 t/h);刀片:65Mn钢,220×70×6mm。
小型铡草机?
外观与结构:小型铡草机为农业用饲料加工设备,用于切碎秸秆、青贮等物料;有齿轮传动型和输送带传动型两种主流结构;配备进料斗、刀盘、动定刀组、传动部件(齿轮或V型皮带+输送带)、电机或发动机接口;机身材质为钢板,颜色未说明。
图上标注:图上无参数标注
9ZT-3?
外观与结构:揉丝铡草机,适用于3–4吨/小时级农场作业;含32把揉丝刀、加长双孔切割刀、铁链输送机构;机身板厚2.7mm;结构含机身、铁链箱、电机箱三件分装;材质为金属,颜色未说明。
图上标注:3.8 t/h kneading chaff cutter;power: 5.5kW three-phase 380V copper motor, or 15HP petrol engine / 178 diesel engine;weight: body about 103kg + motor about 49kg;overall size about 174×106×140cm;packed as body (about 0.314 CBM) + iron chain box + motor box;3 t/h version available (about 5HP / 6HP motors);only the 3 t/h chain machine has a PVC-belt option
加重款小型铡草机?
外观与结构:小型铡草机的加强耐用版本,机身加厚,结构更稳固;未说明外观颜色与材质细节。
图上标注:heavy-duty version;thicker body;body about 49kg (standard about 43kg);about 72–73kg with motor
加固定板款小型铡草机?
外观与结构:小型铡草机的强化版本,采用加长使用寿命的固定板设计;输出能力与标准款相同;未说明外观颜色与材质细节。
图上标注:reinforced fixed-plate version;longer service life;same output
Chaff cutter 9ZT-6.5 / 93QS-6.5 (6.5 t/h)?
Capacity about 6.5–8 t/h; 6 moving blades + 48 kneading blades; powered by a 12HP 192F air-cooled electric-start diesel; size about 2200×695×1090mm; packed in wooden cases. 原文备注:与宣传册参数核对。
9ZT-0.4 铡草机的标准配置和产能是多少??
9ZT-0.4 系列是主推小型铡草机。标配为2.2kW(铭牌标3HP)铜线单相电机,220V/50Hz,转速约2800rpm。产能约0.4–1.0 t/h,取决于物料:干草约0.4 t/h,玉米秸秆可达约1.0 t/h。切割系统为4动刀+1定刀,刀片材质为65Mn钢,尺寸220×70×6mm。该机型也可提供汽油机或柴油机机架版本。
9ZT-0.4 铡草机的刀片数量有哪些选项?揉丝刀是什么??
标准小型铡草机为4动刀+1定刀,刀片为65Mn钢,220×70×6mm(比常见的5mm刀片更厚)。5刀版需加高机身,仅限齿轮式机型可做;6刀版最小起订量为50台。另可选配揉丝(搓揉)刀,使切碎后的草更细更软。2t/h及以上大型机型标配揉丝刀。
齿轮款与输送带款铡草机有什么区别?0.4A/0.4B/0.4C 是什么含义??
三种结构:(1)齿轮款:料斗喂料,无输送带,通过齿轮杠杆调节切长;(2)输送带款:皮带喂料,无齿轮调长,适合新鲜牧草;(3)齿轮+纹理输送带款:兼具皮带喂料与切长调节功能。9ZT-0.4A为带独立料斗的齿轮款。0.4B/0.4C等后缀因市场而异,定义不统一,下单前须提供实机图片由我方确认具体型号。
Chaff cutter 9ZT-2?
Chaff cutter 9ZT-2: capacity about 2.5 t/h; 3.5kW; with kneading. 原文备注:与宣传册参数核对。
9ZT-0.4 铡草机是否支持汽油机或柴油机驱动??
支持。除电机版外,另有通用机架(engine-frame / rack)版本,可安装电机、汽油机或柴油机。小机型柴油机限用小型风冷型(170型或更小);常用汽油机为7HP(170F),其输出轴规格为Φ20mm、键槽宽5mm。注意:汽油机转向与电机相反,需更换对应皮带轮。2–6.5t/h大型机型可配15HP汽油机或12HP柴油机。
如何为铡草机选择合适的电机功率??
参考建议:小型4刀铡草机(0.4–1t/h):最低1.8kW(2.4HP),推荐2.2kW(3HP);加宽5刀版:需3kW;2t/h链式输送机型:需3.5kW单相(约4.5–4.8HP),6.5HP汽油机不足;3–3.8t/h机型:需5.5kW三相380V或15HP汽油机;6–6.5t/h机型:需12HP柴油机或7.5kW电机。我方电机转速约2800rpm;若使用1400rpm电机,链式机型需配≥160mm大皮带轮。
铡草机电机的旋转方向是否有要求??
有要求。不同型号电机转向不同(顺时针或逆时针),例如铡草机+粉碎机组合机型使用逆时针电机;自吸式粉碎机必须顺时针旋转,否则无法吸料并可能过载;碾米机反转可能导致辊筒螺母松动。我方在外箱标注旋转方向箭头;首次使用前请检查,若转向错误,请提供短视频联系我方处理。
小型铡草机可选哪些配件??
可选配件包括:MCB断路开关、正反转开关、电流/电压表、移动轮、木箱包装、客户Logo印刷。
小型铡草机可选配置与报价规则?
可选配置包括:MCB空气开关(断路器)、正反转开关、电流/电压表、加厚电机皮带轮、1.0mm加厚皮带护罩(标准为0.8mm)、万向轮(通用旋转脚轮)、水泵/发动机支架、7层纸箱或木箱包装、激光雕刻客户logo及客户铭牌。所有选项价格均由销售团队随整机一并报价。
小型铡草机装箱尺寸与重量?
典型小型铡草机装箱数据(主机与电机分装):齿轮型主机约43kg,配电机后总重约66kg;输送带型主机约39kg,纸箱尺寸约550×400×320mm(0.07 CBM),配电机后总重约63kg;9ZT-0.4A主机纸箱约560×460×340mm(0.087 CBM),料斗单独包装;电机箱尺寸450×280×290mm(0.036 CBM,约23kg)。每套总体积约0.1–0.2 CBM,具体以装箱单为准。
小型铡草机集装箱装载数量?
含电机时:20英尺柜约装载175–265台,40HQ柜约375–430台(40HQ通常受重量限制,约27–28吨);不含电机时:20英尺柜约290台,40英尺柜最多约630台。实际数量取决于具体型号、机架类型及纸箱尺寸(如方形加厚底座会减少装载量),最终以订单确认的装箱方案为准。
小型铡草机常见故障原因与处理方式?
Q:齿轮损坏 / 机器发出敲击声 / 运转方向错误。
A:(1)齿轮型产品齿断裂或缺失,多因运输撞击导致——需更换齿轮;若更换后仍不工作,可能滚轴弯曲。(2)动刀与定刀间发出敲击声,表明刀片间隙调整过紧——需重新调整间隙。(3)运转方向错误:请核对电机转向是否与机身箭头标识一致。建议提供短视频以便我方确认并安排备件。
Which chaff cutter capacity to choose?
Chaff cutter range by capacity: small 9ZT-0.4 series 0.4–1.0 t/h (2.2kW, for small farms); widened 5-blade about 0.8–2 t/h (3kW); 93QS-2 about 2 t/h and 9ZT-2 about 2.5 t/h (3.5kW, with kneading); 3.8 t/h kneading (5.5kW three-phase or 15HP petrol); 6–6.5 t/h (12HP diesel). Kneading machines make the grass softer and finer for cattle and sheep. To recommend a model, tell us animal number, material (dry/fresh grass, corn stalk) and power supply. We do not have a 10 t/h model. 原文备注:与宣传册参数核对。
小型铡草机 9ZT-0.4A?
外观与结构:齿轮式小型铡草机,带独立料斗,通过齿轮杠杆调节切长;无输送带;适用于干草类物料。
图上标注:型号:9ZT-0.4A;图上无参数标注。
Electric-start diesel battery shipping?
Electric-start diesel engines are normally shipped without battery, because batteries cannot be shipped by sea as normal cargo — please buy a battery locally.
Diesel engine maintenance and replacement?
Our single-cylinder diesels have no spark plug; they rely on the injector and high-pressure fuel pump. If the engine has not been used for a long time, check injector spray. Please use proper engine oil. Replacing with a bigger engine (e.g. 15HP to 30HP) also needs a new pulley/coupling, belt and reinforced base.
9ZT-6.5?
外观与结构:大型铡草机,适用于农场级大产能作业;标注为柴油机型;结构含重型机身、动力传动系统、进料与出料机构;材质为金属,颜色未说明。
图上标注:6–6.5 t/h large chaff cutter;9ZT-6.5 diesel
6.8 t/h chaff cutter?
6.8 t/h chaff cutter: can use 12HP diesel or 7.5kW motor. 原文备注:与宣传册参数核对。
Chaff cutter 9ZT-0.4 series?
Small 9ZT-0.4 series: capacity 0.4–1.0 t/h; 2.2kW; for small farms. 原文备注:与宣传册参数核对。
Chaff cutter 93QS-2?
Chaff cutter 93QS-2: capacity about 2 t/h. 原文备注:与宣传册参数核对。
Pellet machine single-phase or three-phase?
KL125, KL150 and KL160 can be made with 220V single-phase motors. KL210 and above require 380V three-phase power (or a diesel engine). For KL180, please confirm with our sales team whether single-phase is suitable for your order. Three-phase pellet machine motors can be made in 440V/50Hz on request; 220V/60Hz and 110V/60Hz versions of small models are also possible but need confirmation. Please tell us your local voltage, phase and frequency. 原文备注:KL180 是否可单相存在两种说法;60Hz 机型是否有现货需确认。
Differential type vs back-wheel type pellet machine?
We offer two drive structures. Back-wheel (coupling) type: the drive shaft is exposed and uses an oil seal; simpler and lighter. Differential type: integrated closed gear transmission, no oil seal needed, more stable, heavier, less load on the motor — better quality, recommended. For KL160 the differential version must use a larger motor. Differential versions are heavier (e.g. KL160 about 160kg, KL150 about 130kg complete). 原文备注:与宣传册参数核对。
9ZT-0.4 配套标准电机?
外观与结构:单相2极铜线电机,带电缆、皮带轮,外壳为铸铁或铝合金;默认不带插头,线长约1.3m;可按需加装欧标/英标/美标/南非标插头。
图上标注:型号:未注明;功率:2.2kW(3HP铭牌);电压/频率:220V/50Hz;转速:约2880rpm;重量:22.5–23.3kg(铝线版约21kg);皮带轮孔径:24mm;包装箱尺寸:450×280×290mm;体积:约0.036 CBM。
93QS-2?
外观与结构:铁链输送式揉丝铡草机,含5把切割刀片及揉丝刀片,用于高产能饲料加工;结构含机身、铁链输送机构、电机/发动机安装框架;材质为金属,颜色未说明。
图上标注:nameplate 93QS-2A;capacity about 2.0 t/h;power: 3.5kW single-phase copper motor, or petrol-engine frame (15HP);weight: body about 75.6kg + motor about 31kg;packed in three cartons: body about 0.122 CBM, iron chain about 0.089 CBM, motor about 0.037 CBM;V-belt A1180;PVC-belt kneading version available as 9ZT-2 (about 2.5 t/h, 3.5kW 220V)
加宽5刀铡草机?
外观与结构:小型铡草机的加宽升级款,机身宽度约275–300mm(标准为250mm),采用链条替代齿轮定位板,适配3kW电机;结构强化,但未说明外观颜色与材质细节。
图上标注:widened 5-blade gear model;capacity about 800–2000kg/h;uses a chain instead of the gear positioning plate;needs a 3kW motor
小型铡草机易损件与备件?
外观与结构:无独立外观描述,属配套耗材类。
图上标注:blades (220×70×6mm, 4 per machine);blade disc assembly;V-belt (usually A1100; some models A1200/A1250/A1270);conveyor belt (3mm thick, 237mm wide, 1100/1200mm long; PVC or textured);large gear (ductile iron) and connecting gear;chain;feed fingers;motor pulley;hopper/chute;motor cover;wheels;250µF start capacitor for the motor
6 t/h chaff cutter?
6 t/h chaff cutter: uses a 12HP water-cooled hand-crank diesel (electric start optional); about 240kg. 原文备注:与宣传册参数核对。
Widened 5-blade chaff cutter?
Widened 5-blade chaff cutter: capacity about 0.8–2 t/h; 3kW. 原文备注:与宣传册参数核对。
3.8 t/h kneading chaff cutter?
3.8 t/h kneading chaff cutter: 5.5kW three-phase or 15HP petrol. 原文备注:与宣传册参数核对。
Chaff cutter with grinder combo 9ZT-0.4-G200?
Combines a conveyor chaff cutter (with gear adjustment) and an 8-inch grinder head. Grinding capacity about 0.4–0.6 t/h; smallest sieve 1mm. Standard motor 2.2kW, turning counter-clockwise. Weight: machine about 72kg + motor about 23kg; packed in body carton (about 0.12 CBM), belt box and grinder box (2 heads per box); 100 sets are about 11 CBM. 原文备注:与宣传册参数核对。
Guillotine kneading crushing machine?
Guillotine kneading crushing machine: 24 kneading blades plus 12 cutting blades; cuts and shreds grass/straw finely. Power: 2.6–3.0kW single-phase motor or 7HP petrol engine. Capacity about 0.4–1.0 t/h. Weight: machine about 56kg + motor about 26kg; machine box about 800×455×570mm (0.21 CBM), hopper packed separately; about 0.32 CBM per set in total. It is popular in Africa. 原文备注:与宣传册参数核对。
3-in-1 kneading and crushing machine?
Kneads grass and crushes grain: about 200kg/h for grain/crushing and about 1.0 t/h for fresh corn stalk. It has 3 blade plates, 3 main blades, 12 small blades and 24 hammer blades. Motor 3kW 220V, 2880r/min; weight about 80kg; sieves 6/10/30mm. A wheeled version with 170F 7.5HP petrol engine is also available — it cuts corn stalk and grinds corn grain, with big wheels and handle-adjusted belt tension. 原文备注:数据仅一两次出现;与宣传册参数核对。
Banana tree cutter?
Banana tree cutter: about 500–700kg/h, 2.2kW 2800rpm motor, cuts stems up to about 200mm diameter; the new version has about 18 small internal blades. Weight: machine about 31kg + motor about 23kg; carton about 720×250×590mm (0.106 CBM). It can also be supplied with petrol or diesel engine. 原文备注:与宣传册参数核对。
Engine options: 168F, 170F, 173F, 177, 190F, 192F, water-cooled diesel, electric-start diesel?
Engines supplied: 168F petrol about 4HP; 170F petrol about 7HP (nameplate often 7.5HP), 3650rpm; 173F air-cooled diesel about 8HP, about 23–26kg; 177 petrol about 9HP; 190F/192F petrol about 15HP; 192F diesel about 12HP; water-cooled hand-crank diesel 8HP / 12HP (about 102kg) / 15HP (about 150kg); electric-start diesel 22HP / 25HP / 30HP. 原文备注:190F/192F 马力说法有出入(10hp/14hp/15hp);与宣传册参数核对。
Feed pellet machine KL series (KL125, KL150, KL160, KL180, KL210, KL230, KL260, KL300, KL400)?
Reference capacity and power: KL125 60–75kg/h, 4kW single-phase; KL150 75–140kg/h, 4kW; KL160 100–150kg/h, 5.5–5.8kW; KL180 125–160kg/h, 5.8kW (largest single-phase model); KL210 250–300kg/h, 7.5kW three-phase or 12HP diesel; KL230 300–350kg/h, 11kW or 15–18HP diesel; KL260 400–500kg/h, 15kW or 20–22HP diesel; KL300 500–600kg/h, 22kW or 32HP diesel; KL400 1000–1250kg/h, 32–37kW three-phase. Output depends on material and die size. 原文备注:颗粒机产能存在多套口径(如 KL160 100-150/120-150/150-200,KL400 电机 32/37KW);与宣传册参数核对。
颗粒机汽油机/柴油机款动力配置(KL150–KL300、500)?
可选汽油机或柴油机。KL150/160汽油款后轮式配约7–9HP;KL160建议配15HP(190F)汽油机,7HP偏小。KL160柴油款配8–9HP柴油机(可选水冷)。190型(roller type)可用8HP汽油机。KL210配12HP柴油机;KL230配15–18HP;KL260配20–22HP;KL300配32HP柴油机。500型不能配汽油机。原文标注待核实,需与宣传册参数核对。
颗粒机包装尺寸与重量(KL125–KL400)?
木箱包装约:KL125约0.14 CBM/85kg;KL150 83×35×56cm,约0.14 CBM/86kg;KL160约0.15–0.2 CBM/88–102kg;KL180约103kg;KL210约0.38–0.52 CBM/约230kg;KL230 130×48×82cm,0.52 CBM/250kg;KL260 148×55×96cm/约305kg;KL300约1.0 CBM/500kg;KL400 182×57×153cm,1.6 CBM/800kg。差速款更重。单个木箱免熏蒸。最终数据以装箱单为准。原文标注待核实,需与宣传册参数核对。
颗粒机开关与接线安全?
2.2kW以上机器通常不配插头,配空气开关(断路器),这是行业安全做法;我们所有颗粒机均带空开。可选:带防尘盒空开、接触器或白色电控箱。安装时不要用插头,使用至少4mm²铜线(长距离用6mm²)和32A或更大空开;黄绿线必须接地。每台电机出厂前测试功率、电流和转向。
颗粒机易损件与备件(KL125–KL400)?
主要易损件为模盘(平模)和带轴承的压辊。其他备件:立轴、万向节、料斗、差速器、螺栓与筛网套装、开关/控制箱。各型号(KL125至KL400)模盘孔径2.5–8mm可选。建议随机订购1–2个备用模盘。询价备件请提供型号和模盘孔径,由销售团队报价。
生物质颗粒机(200/250/350)与饲料颗粒机(KL系列)?
我们的饲料颗粒机(KL系列)不能做木屑颗粒,木屑需要更高压力和温度。木屑/生物质颗粒我们供生物质颗粒机:型号200、250、350,配柴油机(如200配15HP、250配25HP、350配35HP,配8mm模盘约500kg/h),200型也可配11kW 380V电机。每台机器含2个筛网。也可按要求提供饲料膨化机/挤压机(包括浮性鱼饲料)。原文标注参数仅少数来源,待核实。
自吸式粉碎机 9NT-26 与 9NT-28?
两者均为自吸式谷物粉碎机(用软管吸料)。26型:粉碎室约250mm,电机2.2–3kW(4HP);带电机约48kg,约0.11–0.13 CBM。28型:粉碎室280mm,电机3–4kW,约500–600kg/h;机身约39kg+电机;约0.145 CBM。26型与28型配件不通用。电机必须顺时针转才能自吸。可加人工料斗,实现自吸/人工两用。原文另注:26型产能有150-180/300-400/350-450kg/h多种说法,待核实;需与宣传册参数核对。
粉碎机筛网孔径与电机负载?
Q: What screen sizes are available? / Can it grind very fine flour? A: 26 型自吸粉碎机标配筛网 1–6mm,最大 8mm(没有 7mm);另有细筛 0.4mm 和 0.6mm(没有 0.5mm)。其他粉碎机筛网约 0.8mm 到 8mm。筛孔越小,电机负载越大;很细的筛网(如 0.2mm)需要配更大电机,避免烧电机。
定制筛网起订量与备件订购?
Custom screen sizes need a minimum of 500 pieces. Spare screens can be ordered with the machine. 定制筛网最少 500 件;备用筛网可随机订购。
不锈钢粉碎机?
不锈钢粉碎机:2.2kW copper motor;dry corn about 200–300kg/h;fitted with air switch;no wheels;dry material only (not for wet). 中文:2.2kW 铜电机,干玉米约 200–300kg/h,带空气开关,无轮子,只能磨干料,不能磨湿料。
G系列万能粉碎机 G150?
G-series universal grinder G150 with stainless hopper: uses about 3HP. 原文仅给出以上参数。
G系列万能粉碎机 G200?
G-series universal grinder G200: uses 2.2kW motor or 7HP petrol; about 40–100kg/h; body about 28–31kg. 原文待核实:G200 产能有 40-80/80-100kg/h 两说,需与宣传册参数核对。
G系列万能粉碎机 G260?
G-series universal grinder G260: uses 4kW motor or 15HP petrol; about 100–200kg/h; packing about 72×43×44cm (0.14 CBM).
8英寸粉碎机头 200?
8-inch grinder 200 can grind both dry and wet. 原文仅给出干湿两用这一参数。
10英寸粉碎机头 260?
10-inch grinder 260 handles wet beans about 300kg/h. 原文仅给出湿豆约 300kg/h 这一参数。
粉碎机 9FC-21?
9FC-21 grinds grain only; uses 3HP copper motor or 2.2kW. 中文:9FC-21 只磨粮食,3HP 铜电机或 2.2kW。
CE认证适用范围?
公司持有ISO 9001质量管理体系认证;铡草机和颗粒机已取得CE证书;大额订单可另行安排单独CE认证。
自吸粉碎机(2.6kW)?
Suction mill (2.6kW): dry grain and dry chilli only, not wet. 中文:自吸粉碎机 2.6kW,只适合干粮食和干辣椒,不适合湿料。
粉碎机类型与适用物料选择?
Q: Can the grinder crush corn cob and straw? / Can it grind wet material? A: 按物料选择:9FC-21 只磨粮食(3HP 铜电机或 2.2kW);9ZF-50 可磨粮食和秸秆/玉米芯(3kW 铜电机);爪式 9TF-320/360 为大机型(7.5–11kW,按筛网约 900–2000kg/h);自吸粉碎机(2.6kW)只磨干粮食和干辣椒,不磨湿料;不锈钢粉碎机只磨干料。湿料(泡豆、浆料)请用胶体磨/磨浆机或 8/10 英寸粉碎机头。请告知物料和所需细度。
自吸粉碎机吃力发热排查?
Q: The grinder is hard to run / bearing gets hot / it doesn't suck material. A: 请检查:(1) 电机转向——自吸粉碎机必须顺时针转,反转会不上料且负载重;(2) 断电后手转转子,确认转动顺畅;(3) 筛孔是否太小,孔越小负载越大;(4) 供电电压和电缆线径。请发一段机器运行视频(带声音),技术员会协助诊断并在需要时安排配件。
磨浆机 150?
Model 150: 1.1kW, wet/dry with converter — steel discs for dry, emery (sand) discs for wet; sesame about 15kg/h, peanut/nuts 8–10kg/h, dry grain about 30–60kg/h; carton 57×52×43cm, about 34kg. Models 150 and 160 can grind dry roasted peanut and sesame. 原文待核实:150 型干料产量有 50kg/h 与画册 30-60kg/h 不一。
磨浆机 160?
Model 160: 2.2kW, emery discs only, stainless hopper, about 42kg. Models 150 and 160 can grind dry roasted peanut and sesame. 中文:160 型 2.2kW,只用砂磨盘,不锈钢料斗,约 42kg;150/160 可磨干炒花生和芝麻。
磨浆机 200?
Model 200: iron hopper, electric about 48.5kg or petrol about 39kg. 中文:200 型为铁料斗,电动款约 48.5kg,汽油款约 39kg。
磨浆机 260?
Model 260: three-phase motor or 190 petrol engine, about 85kg. 中文:260 型配三相电机或 190 汽油机,约 85kg。
花生酱机 100(SS100)?
Model 100 (SS100): 1100W, about 10–20kg/h, white-steel grinding stones about 155mm, size about 30×30×70cm, about 21kg. Spare grinding stones are available. 中文:100 型(SS100)1100W,约 10–20kg/h,白钢磨石约 155mm,尺寸约 30×30×70cm,约 21kg;可配备用磨石。
花生酱机 160?
Model 160: about 30kg/h, 1500W. Spare grinding stones are available. 中文:160 型约 30kg/h,1500W;可配备用磨石。
小型碾米机 6N40?
6N40 single rice mill: about 180–250kg/h (household use about 150–200kg/h), 3HP/2.2kW copper motor or 7HP petrol engine, machine about 60kg. Versions: basic, and one with vibrating sieve. 中文:6N40 单机约 180–250kg/h(家用约 150–200kg/h),3HP/2.2kW 铜电机或 7HP 汽油机,机器约 60kg;有基本款和带振动筛款。
组合米机(带21爪粉碎机与分离器)?
Combined rice mill adds a 21-claw grinder and separator (rice milling + flour), with 1x or 3x air blowing, two-stage separation, hand-wheel gear and forward/reverse switch. Combined set about 72–87kg, about 0.175 CBM; a 40HQ holds about 360 sets with petrol engines. 中文:组合米机增加 21 爪粉碎机和分离器(碾米+磨粉),配 1 次或 3 次吹风、两级分离、手轮齿轮和正反开关;整套约 72–87kg,约 0.175 CBM;40HQ 装汽油机款约 360 套。
大产量碾米机 6N70 / 6N130 / 不锈钢碾米机?
原文仅列出产品名称/关键词:Rice mill 6N70;high capacity rice polisher;6N130;stainless steel rice mill。原文未给出功率、产量、包装等参数。
6N70 碾米机?
6N70 高产能碾米机:产能约400–600kg/h;配380V 7.5kW三相1400rpm电机或12HP柴油机;米辊D70×310mm;仅用于碾米/抛光。可选配提升机、回风管、中筛或磨粉机。机器净重约95–100kg(不含提升机),木箱约0.4–0.5 CBM;带提升机约1.4 CBM,分4箱。原文备注:净重有95/96/99kg多种说法,需与宣传册参数核对。
6N130 碾米机?
6N130 碾米机:产能约1000kg/h,配7.5kW三相电机。原文仅列出上述产能与配套动力,未给出米辊、重量、包装或可选配置信息。
碾米机易损件(米筛、米辊、轴等)?
碾米机易损件包括米筛、磨盘和粉筛。米筛有普通钢、锰钢、不锈钢和淬火不锈钢;米辊仅为铁质。另可供应轴、开关、风扇总成和皮带(A/B型)。
碾米机轴断或米辊窜动是什么原因??
碾米机轴断或米辊横向窜动,通常原因是电机反转导致两侧紧固螺帽松动。处理方式:纠正电机转向,并重新拧紧两侧螺帽。
玉米剥皮脱粒机?
玉米剥皮脱粒机:无需去除苞叶即可剥皮并脱粒;产能≥1500kg/h;配7HP汽油机或1.8–2.2kW电机。原文未给出型号、重量和包装信息。
多功能脱粒机?
多功能脱粒机:可用于玉米、大豆、水稻、小麦、高粱脱粒;配3kW 220V铜线电机或7HP汽油机,木箱包装。原文未给出型号、产能、重量和外形尺寸。
小型木材粉碎机?
小型木材粉碎机:配7HP汽油机,产能约600kg/h,3片刀片,可处理6–8cm树枝;木箱尺寸97×38×85cm(0.32 CBM),不含发动机约85kg。
新款树枝粉碎机?
新款树枝粉碎机:配7HP汽油机,产能约2t/h,可粉碎干或湿树枝5–8cm,整机约105kg。原文未给出型号、刀片数量和包装尺寸。
木材粉碎机 150?
木材粉碎机 150:配188F/192F电启动柴油机,可处理最大约5英寸树枝,出料木片3–5cm。该机型无现货,按订单定制。
木材粉碎机 200?
木材粉碎机 200:配188F柴油机,可处理小于4英寸(under 4 inch)的树枝。该机型无现货,按订单定制。
木材粉碎机 300?
木材粉碎机 300:配192F柴油机,可处理小于5英寸树枝,产能1–2t/h。该机型无现货,按订单定制。
木材粉碎机可配哪些柴油机?168柴油机适用吗??
木材粉碎机 150 可配188F/192F电启动柴油机,200配188F,300配192F;原文明确不建议将168柴油机用于木材粉碎机。木材粉碎机按订单定制,无现货。
不锈钢卧式饲料搅拌机 50kg?
不锈钢卧式饲料搅拌机 50kg:每批50kg,配1.1–1.5kW全铜电机,默认220V,每批约2–5分钟,木架包装。该系列仅电动,无柴油/汽油版本;不锈钢不能喷红色。
不锈钢卧式饲料搅拌机 100kg?
不锈钢卧式饲料搅拌机 100kg:每批100kg,配1.5–2.2kW全铜电机,默认220V,每批约2–5分钟,木架包装。该系列仅电动,无柴油/汽油版本;不锈钢不能喷红色。
不锈钢卧式饲料搅拌机 150kg?
不锈钢卧式饲料搅拌机 150kg:每批150kg,配2.2–3kW全铜电机,默认220V,每批约2–5分钟,木架包装。该系列仅电动,无柴油/汽油版本;不锈钢不能喷红色。
不锈钢卧式饲料搅拌机 200kg?
不锈钢卧式饲料搅拌机 200kg:每批200kg,配约4kW全铜电机,默认220V,每批约2–5分钟,木架包装。该系列仅电动,无柴油/汽油版本;不锈钢不能喷红色。
立式螺旋饲料搅拌机 300kg?
立式螺旋饲料搅拌机 300kg:每批300kg,配约4kW电机。原文未列出电压、材质、包装或每批混合时间。
立式螺旋饲料搅拌机 500kg?
立式螺旋饲料搅拌机 500kg:每批500kg,配约4kW电机。原文未列出电压、材质、包装或每批混合时间。
平底饲料搅拌机 200kg?
平底饲料搅拌机 200kg:用于饲料混合;向玉米粉中加水时,含水量不应超过30%。原文未列出配套动力、电压、材质和包装信息。
饲料搅拌机电动配置与运输计费?
饲料搅拌机仅做电动版本,无柴油或汽油版本;不锈钢材质不能喷红色。搅拌机体积较大,运费按体积计算。
螺旋提升机?
螺旋提升机:长度1.5m至4m,规格为1.5/2/2.5/3/3.5/4m,配2.2kW 220V电机;可选更大16cm管径。原文备注:数据来源少,需核实。
3米饲料输送机?
3米饲料输送机:外形约2.7×0.55×0.70m,重量约50kg。原文未列出输送量、电机功率和材质。
管道输送机?
管道输送机:3.5英寸管径,长度12m,配4.5–5.5kW电机。原文未列出输送量、材质和电压信息。
小型饲料线组合?
小型饲料线组合:可由200型搅拌机、提升机和260颗粒机组成。原文未列出该组合的产能、总功率和占地尺寸。
20型窗式切菜机?
20型窗式切菜机:304不锈钢,配0.4kW 220V电机,双速;可切片、切丝,不能切丁。原文未列出产能和外形尺寸。
180单头切菜机?
180单头切菜机:配1.5kW电机,产能300–500kg/h,进料口270×200mm;标配3把刀(切丝3mm、切片3mm、切丁15mm)。
五合一切菜机?
五合一切菜机:可切片2–4mm,切丝2mm,切条/波浪8/10/14mm,切丁10mm(可选10–25mm)。原文未列出功率、产能、材质和外形尺寸。
擦丝机 400/500?
擦丝机 400/500:可切丁、切片和切丝。原文未列出两种规格各自的功率、产能、材质和外形尺寸。
蔬菜切碎机?
蔬菜切碎机:201不锈钢,铜线电机,随附刀和勺。原文未列出型号、功率、产能和外形尺寸。
切菜机备用刀组?
切菜机备用刀组:原文说明可提供备用刀组,但未列出适用机型、材质和规格;采购时需按具体切菜机型号确认。
非标电压/相数定制?
非标电压/相数定制:标准电机为220V/50Hz单相(小机器)和380V/50Hz三相(大机器)。非标电压或相数(如220V三相、大单相60Hz电机)需定制,通常起订量约30–50台。部分小机器(如26 grinder、小型颗粒机、面粉机)做过110V/60Hz或220V/60Hz,需与销售确认。报价前请告知电压、相数和频率。原文备注:定制起订量30或50台说法不一,需确认。
颗粒机模盘孔径选择(KL系列)?
颗粒机模盘/孔径可选2.5mm、3mm、4mm、6mm、8mm,用于鸡、鱼、牛等。标配模盘为4mm;可选孔径2.5/3/4/5/6/8mm(2.5mm最小,没有2.2mm)。选型:2.5–4mm用于小鸡、鸭、小猪;6mm用于羊和小牛;8mm用于大牛和马。KL180/210配6mm;KL210可另配4mm和8mm模盘。2.5mm模盘孔数更多、成本更高。物料含水率约10–20%。模盘寿命通常数月,视使用情况而定。
不锈钢立式碾米机?
不锈钢立式碾米机:配2.2kW电机,产能约200kg/h。原文只给出功率与产能,未列出型号、米辊、重量、包装或可选配置信息。
颗粒机压辊数量与模盘直径(KL125–KL400)?
压辊:KL125、KL150两辊;KL160三辊;KL180四辊;KL210三辊(也可做两辊款);KL260三辊;KL300、KL400四辊。模盘直径:KL150约138mm;KL160/KL180约148mm(KL160小款138mm);KL210约210mm。125/150/160压辊工作宽度约35–40mm。原文标注待核实,需与宣传册参数核对。
爪式粉碎机 9TF-320/360?
Claw-type 9TF-320/360 are larger: 7.5–11kW, about 900–2000kg/h depending on screen. 中文:爪式 9TF-320/360 为较大机型,7.5–11kW,按筛网不同约 900–2000kg/h。
磨面机 2.2kW?
2.2kW flour mill (with voltage meter box) is dual-use: about 50kg/h flour or about 100kg/h paste. Screens: 40, 60, 80, 100, 120 mesh — 80 mesh is installed, and one each of the other four is included. Use steel discs for dry grinding; emery discs are for wet and can crack if over-tightened or used dry. Packing: machine about 58×34×54cm (about 35kg) + motor box 45×27.5×29cm (23kg), total about 0.14 CBM / 58kg. A 2.4kW 60Hz version is also available. 原文待核实:磨面机包装重量有 34.6/36kg 两说。
玉米脱粒机 5TY-46-86?
5TY-46-86 单辊玉米脱粒机:产能约800–1200kg/h,配0.75–0.95kW电机2800rpm;双辊版本约1500W,产能更大。整机约34kg,约0.1 CBM;20GP约装350台。可选配7HP汽油机版本。原文备注:参数需与宣传册核对。
加工特定数量物料需要多长时间??
可用简单公式估算:小时数 = 物料重量(kg) ÷ 机器产能(kg/h)。例如,30 kg物料在60 kg/h机型上约需半小时。实际产量受物料种类、含水率、筛网或模孔尺寸影响,建议预留余量。
Feed mixer 75 kg?
Capacity (reference): about 75 kg per batch. Power options: 3 kW motor. Voltage: 220V. Machine size: about 91 × 63 × 110 cm (stainless steel). Weight: —. Packing size: —. CBM: —.
77. The corn sheller cannot grip some cobs or stops often. What should I do?
Corn cobs vary in size, so adjust the inlet opening with the adjusting handle to suit your cobs. Feed evenly and do not push too many cobs in at once. If it still stops, send us a video so we can check the speed and settings.
Mixer 150 kg?
Capacity: About 150 kg per batch. Power: 3–4 kW motor. Voltage: 220V. Machine size: About 82 × 82 × 111 cm (drum about 84 cm). Weight: About 57 kg. Packing size: About 82 × 82 × 111 cm. CBM: About 0.75.
电机应配何种电缆和断路器??
必须通过空气开关(MCB)或专用启动器连接电机,严禁使用家用插座、延长线或插线板。须使用截面积至少2.5mm²的铜芯电缆,并尽量缩短长度;我方技术人员建议控制在约8米以内,因过长或过细的电缆会导致压降,使电机动力不足。参考值:220V下2.2kW电机满载运行电流约10A。请咨询当地电工,按电机参数选配断路器。
能否购买不带电机的机器??
可以。大多数型号可不配电机供货,例如客户已在当地备有电机或发动机。我方可按需加装皮带轮或发动机底座。请确保您自备电机的功率与转速与机器匹配。部分机型(如混合机)仅提供带电动机版本。
你们配备哪种汽油发动机?油耗多少??
小型机器通常配备约7HP(212cc)的170F型四冲程汽油发动机,带手拉启动装置。参考值:满载时油耗约1.2–1.6升/小时;3.6升油箱续航约2.5–3.3小时。实际数值依负载而异,请向我方销售团队确认。
汽油发动机是否附带机油和电池??
汽油发动机发货时不包含发动机机油和燃油。首次使用前,请加注机油至油标尺刻度线,再加入普通汽油。电池不可运输,因此电启动发动机需客户在当地另购12V摩托车用电池;手拉启动发动机无需电池。
应选择汽油发动机还是柴油发动机??
汽油发动机更轻便、成本更低,是小型机器最主流的选择。柴油发动机价格显著更高、振动更大,但更适合重载、长时间作业,以及柴油更易获取的地区。对于碾米机,我们建议选用电动机或汽油发动机,因柴油机振动更强。大型柴油发动机可配电启动;小型柴油机为手拉启动。
柴油发动机首次使用前如何准备??
向燃油箱加注柴油,向水冷式发动机的水箱加注冷却水,并检查发动机机油液位后再启动。发动机出厂时不含任何液体(油、水、燃料),以保障运输安全。若为电启动发动机,请连接客户在当地采购的12V电池。我方团队可提供图片或视频,说明各加注口位置。
为什么货代测量的CBM与贵方数据不同??
我方包装尺寸为预估值,实际装箱后可能略有变化,纸箱在运输中也可能轻微膨胀。货代测量时常在每边额外增加几厘米。您可向货代索要其测量记录。如差异较大,请告知我方,我们将重新测量包装并提供照片,以便核查差异原因。
能否进一步拆解机器以降低CBM??
原文未提供答案。
How many packages will I receive for one machine?
Most machines ship as several packages, for example machine body, hopper and motor packed separately, and a combined rice mill set usually ships as 4 to 5 packages. Engines and motors are often packed alone. The packing list shows the number of packages for each item, so please check the total count with your forwarder on arrival.
Can the machine and motor be packed in one case?
By default the machine and motor are packed separately, which protects them and keeps the volume low. Packing them together requires a wooden case at extra cost. Please tell us before production if you want this.
When should I choose wooden case packing?
We suggest wooden cases for long sea routes with several transshipments, for heavy or cast iron machines, and when goods may be handled roughly. Pellet machines and large combined machines are normally packed in wooden cases, while small machines use strong export cartons. Wooden cases add some cost and volume, so please decide before packing.
获取准确报价需要提供哪些信息??
请告知我们您想要的型号或待加工物料、每小时所需产量、采购数量、电源规格(电压、相数、频率)、动力偏好(电动机、汽油机或柴油机)、目的港,以及您是否在中国有货运代理。销售团队将据此推荐合适配置并发送正式报价。
机器价格是多少??
价格取决于型号、数量、动力配置(电动机/汽油机/柴油机)、电压及包装方式。请提供具体型号、数量、目的港和当地电压,销售团队将为您发送正式报价。
所报价格仅含主机,还是整机成套??
正式报价中会明确说明包含内容,例如:主机+电动机,或主机+汽油机,以及包装和运至您在中国的货代仓库(如需)。部分线上列表仅显示主机(不含电机或发动机)。请说明您需要的配置,销售团队将确认整机成套报价。
应选择220V家用型还是380V农场型??
一般而言,220V单相机型适用于家庭及小型农场,产量约60–300 kg/h(依机型而定);380V三相机型适用于农场及小型加工企业,产量约350–1250 kg/h。以上为参考范围,实际取决于配置;请与销售团队确认。若无三相电源,可考虑柴油机版本。
为何产能标为范围而非单一数值??
产能并非固定值,它取决于原料种类、含水率、筛网或模孔尺寸,以及操作者喂料均匀程度。对粉碎机而言,筛孔越大,产量越高;极细筛网则大幅降低产量。我们提供真实范围,便于您合理规划。
KL系列饲料颗粒机的预期产量是多少??
参考值:KL125约40–60 kg/h,KL150约60–100 kg/h,KL160约100–200 kg/h,KL300约600–1000 kg/h,具体取决于物料、含水率和模孔尺寸。如需约150 kg/h,建议选择KL160或更大机型,而非KL150。以上为参考值,实际取决于配置;请与销售团队确认。
颗粒机能同时完成粉碎和混合吗??
不能。颗粒机仅用于制粒。原料须先经粉碎机磨成粉状,并在配方需要时用混合机混匀。许多买家会配套采购粉碎机、混合机和颗粒机,组成小型饲料生产线。所产颗粒可用于鸡、鸭、猪、牛、羊、兔、马及鱼类。
能否调节颗粒长度??
可以。颗粒长度可通过切刀调节螺钉大致调节为1–2.5 cm:拧紧使颗粒变短,松开使颗粒变长。颗粒直径由模孔尺寸决定,因此请在订购机器时一并订购所需模孔规格。
是否有小于2.5 mm的颗粒模孔,适用于雏鸡或鹌鹑??
我们供应的最小模孔为2.5 mm,适用于雏鸡、鹌鹑及小型鸟类。小孔径模孔在处理软质或叶状物料时更易堵塞,且产量显著降低,因此许多用户会同时备有4 mm模孔。请告知您的养殖动物种类及所用物料,我们将推荐合适的模孔尺寸。
贵司颗粒机能否生产浮性鱼饲料??
平模颗粒机生产沉性颗粒。浮性鱼饲料需使用饲料膨化机(浮性鱼饲料机),其工作原理不同,且操作需一定经验。请告知您的鱼种、所需颗粒尺寸及产量要求,销售团队将确认适用机型。
贵司粉碎机能否生产供人食用的细面粉??
我司多数锤片式粉碎机及粉碎设备主要针对动物饲料设计,可将干玉米、谷物粉碎为粉料,但并非专用于生产精细食用面粉的磨粉设备。最细筛网为0.2 mm;使用该筛网时产量骤降至约80–100 kg/h,筛网易快速磨损,电机负荷增大。多数用途推荐使用约0.6 mm筛网。请说明您所需的细度,我们将如实提供建议。
碾米机能去除稻谷中的石子和沙子吗??
组合式碾米机配有振动分选筛,可分离整米、碎米及大于米粒的石子。但无法去除细沙。若稻谷含沙,请先用前置清理机或去石机进行预清理。稻谷中混入石子也会加速米筛磨损。
碾米机不能做什么??
碾米机专用于干燥稻谷的砻谷与碾白。它不能用于玉米脱皮、湿料粉碎或制作婴儿米粉。如需玉米粉,请选用粉碎机,或选用带破碎功能的组合式碾米机。请告知您的原料及目标成品,我们将推荐合适机型。
你们是否提供番茄酱、辣椒酱、肉类、骨头、糖、熟米饭、棕榈叶、石头、核桃、椰肉、芝麻脱壳、鹰嘴豆去皮或香蕉切片等设备?是否提供孵化器、咖啡烘焙机、榨汁机、水果烘干机、碎冰机或水稻插秧机??
我们不提供用于番茄酱或辣椒酱、肉类或骨头、糖研磨、熟米饭、棕榈叶、石头、核桃破壳、椰肉、芝麻脱壳、鹰嘴豆去皮或香蕉切片的机器;也不生产孵化器、咖啡烘焙机、榨汁机、水果烘干机、碎冰机或水稻插秧机。我们仅出口农业及食品加工机械。如客户请求超出我方产品范围,我们将明确告知。
你们能否测试贵方此前未测试过的物料??
我厂不常备所有原料,常规测试使用玉米或谷物进行。对于此前未测试过的物料(如可可豆或木薯叶),我们将如实说明结果未经验证。在此情况下,我们建议先订购一台试用机,以便您使用自有物料验证效果,再决定是否批量采购。
螺旋式混合机能处理湿物料吗??
我们的螺旋式混合机适用于常规干饲料物料。对于含水率较高的物料,平底卧式混合机更为合适。为获得最佳混合效果,请勿过量填充混合机;较小批量、多次混合可实现更均匀的混合效果。请告知我们您的具体物料类型及每批次处理量,以便我们推荐合适型号。
能否使用发电机、逆变器或太阳能系统驱动机器??
电动机需要能承受其启动电流(为运行电流数倍)的电源。发电机功率应明显大于电机额定功率:例如,7.5kW的碾米机电机需配10–15kW发电机,3kW粉碎机需配大于3kW的发电机。小型逆变器和太阳能系统常在启动时跳闸,因此我们通常不推荐使用。若电网供电不可靠,建议选择汽油或柴油发动机版本。
能否使用转换器将380V三相机器接入单相220V电源??
不能。三相机器无法通过简易转换器从单相电源正常运行,我们亦不提供此类变压器。若您仅有单相220V电源,请选择单相型号,或选择大型机器的汽油/柴油发动机版本。
能否在60Hz电源环境下使用50Hz电机??
不建议。频率变化会改变电机转速:50Hz电机空载转速约为1400或2800 rpm,60Hz电机约为1700或3400 rpm,整机设计与对应转速匹配。50Hz与60Hz电机、110V与220V电机不得混用,否则可能导致电机过热或损坏。请告知当地电源频率,以便我们配置正确电机。
我的电源是230V或240V单相50Hz,或400V三相,是否需要特殊电机??
通常不需要。例如澳大利亚、尼日利亚或塞内加尔使用的单相220–240V 50Hz电源,一般可适配我方标准220V 50Hz电机;400V三相50Hz电源通常可适配我方380V机型。60Hz、110V及其他电压规格需配置特殊电机。下单前请确认您的确切电压、相数及频率。
How many machines fit in one cubic meter or one container?
As a rough guide, a 20ft container holds about 27 to 28 CBM and a 40HQ about 60 to 66 CBM, and heavy machines may reach the weight limit before the volume limit. Small grinders with motors fit about 3 to 4 units per cubic meter. These figures are for reference, depending on configuration; please confirm with our sales team, who will calculate your exact loading.
Why do you ask whether I have a freight forwarder in China?
For most orders we deliver to your forwarder's warehouse in China, and your forwarder consolidates the goods and handles sea freight and destination clearance. Knowing your forwarder lets us quote the correct domestic delivery and trade term. If you do not have one, you can find forwarders on Alibaba.com, and our sales team can share suggestions; the choice is always yours.
What information do you need to deliver to my forwarder?
Please send the warehouse address and phone number, your warehouse entry number and the shipping mark required by your forwarder, which usually includes your name, phone, entry number, destination country or port and transport mode such as SEA or AIR. Some warehouses also need an entry form. Without the correct shipping mark the warehouse may refuse the goods.
Which forwarder warehouse city is best for delivery from your factory?
Guangzhou is usually the closest and most economical, with delivery in about 2 to 3 days. Foshan, Dongguan and Shenzhen are also close. Yiwu and northern ports such as Qingdao are farther, so domestic delivery takes longer and costs more. Please choose a warehouse that your forwarder uses regularly.
Does the forwarder warehouse charge for unloading?
Many warehouses do not include unloading of heavy items and may charge forklift or unloading fees, especially for wooden cases. Rules differ between warehouses, so please check with your forwarder before delivery and tell us if an appointment is needed. Warehouses also often refuse cash-on-delivery parcels, unlabelled goods and very small parcels.
What will I receive after you deliver to my forwarder?
We send packing photos showing the shipping marks, the size and weight of each package, the domestic tracking number and, when the warehouse provides one, a warehouse receipt. Some express deliveries do not receive an entry slip; in that case we send the signed delivery record or stamped receipt photo for your forwarder.
Who is responsible once the goods reach my forwarder?
Our delivery is completed when the goods are received at your forwarder's warehouse in China. After that, consolidation, international freight, destination clearance and duties are handled by your forwarder and you. We remain available to share tracking numbers, photos and documents to help your forwarder.
How long does sea shipping take to my region?
For reference only: the Philippines about 20 to 30 days, Europe about 40 to 55 days, West and East Africa about 45 to 90 days, many Latin American ports about 45 to 90 days, and Central Asia by sea about 2.5 to 3 months, plus customs clearance and inland transport. Times vary by forwarder, route and season, so please confirm with your forwarder.
Can a whole machine be sent by air or express?
It is possible, but our machines are heavy, so air or express freight for a complete machine is usually very expensive and often costs more than the machine itself. Air or express is best for urgent spare parts. For machines, sea freight through your forwarder is much more economical.
Can my order be shipped in several batches?
Yes. With your agreement we can ship according to the quotation in batches, for example as each model is ready, and different products can be combined in one batch to save freight. Please tell us your plan when ordering so we can arrange production and documents.
Can you deliver to my contact in China instead of a forwarder?
Yes, we can deliver to an address in China that you provide, such as your purchasing agent, office or a friend, who then arranges onward shipment. Please provide the full address, receiver name and phone number.
Packing policy: standard packing, hopper/motor removal, knocked-down options?
Our standard packing is already close to the minimum safe size, and pressing it smaller risks damage. On some models the hopper can be removed or the motor packed separately, but the saving is small. For larger orders, ask us about shipping without motors or in knocked-down form for local assembly.
付款货币与方式?
报价以美元(USD)计价;阿里巴巴平台线上支付默认为美元。人民币(RMB)付款亦可,例如由您在中国的货代或代理凭我方开具的人民币形式发票(RMB proforma invoice)支付。我方无法接收非洲金融共同体法郎(FCFA)、卢比等本地货币付款。
45. 我的银行卡单笔限额低于订单金额,怎么办??
阿里巴巴平台在线订单通常可分两期支付:定金+尾款;银行电汇(T/T)则可分多期支付。若您的银行卡有单笔支付限额,我们也可将采购拆分为多个独立订单。请告知您的限额,我们将为您准备适配的付款链接。
46. 我的在线支付失败了,该怎么办??
常见解决方法包括:尝试另一张银行卡;在阿里巴巴结账页面选择银行转账(T/T),到账需1–2个工作日;联系您的银行开通国际线上支付权限。我们也可重新发送付款链接。若您所在银行或国家限制美元线上支付,请联系我方销售团队咨询T/T或人民币付款方案。
不接受的付款方式?
我方不接受现金、个人支付应用(如微信支付、支付宝个人账户)或支付至个人账户。请仅通过阿里巴巴订单链接中显示的付款方式支付,或按形式发票(proforma invoice)上印制的公司账户信息进行T/T电汇,或经我方销售团队事先确认后,由您在中国的代理以人民币支付。
48. 为什么付款金额必须与形式发票(proforma invoice)一致??
付款金额、形式发票与商业发票(commercial invoice)三者金额必须一致,因银行和海关会比对这三者。金额不一致可能导致银行询证或清关问题。如订单内容发生变更,我们将先更新形式发票及对应付款链接。
49. 如何在阿里巴巴平台上接受交货日期变更??
如约定的发货日期需延长,我方将说明原因并提交修改申请。请您进入‘订单’→‘全部订单’,打开对应订单号,点击接受该修改。平台所计发货日期指货物离境中国之日;延期通常仅可申请一次,故我方仅在必要时使用。
50. 为什么阿里巴巴订单页面显示的交货时间很长??
订单页面显示的交货时间为平台标准设置,已预留节假日缓冲。现货机器通常在付款后约一周内即可发运。每单确切的备妥日期由我方销售团队单独确认。
51. 定制订单需要多长时间??
现货标准机型通常3–7个工作日备妥;小批量生产约7–15个工作日;特殊60Hz电机通常额外增加约1周;110V或120V电机耗时更长;定制颜色或机架通常需25–30个工作日。以上均为参考周期,请务必与我方销售团队确认。
52. 哪些因素会导致订单延迟??
最常见原因包括:需另行采购或定制的特殊电机/发动机;中国节日前的生产旺季;货代截仓日期或仓库关闭。如任何因素影响您的交期,我方销售团队将及时通知并提供生产实拍照片。尽早确认配置细节、优先选用标准配置有助于避免延误。
53. 我的货代仓库在中国节日期间是否开放??
不一定。国庆节(10月初)及春节前后,许多货代仓库会关闭或暂停收货(即使工厂仍在生产),且国内物流在春节前会暂停一段时间。我方将提前告知您中国假期安排,并视情况安排仓库重开后再行交付。
54. 可否订购样品或试用机??
可以。样品按单台价格收费,通常7–15个工作日备妥。您需提供中国境内的货代或收货地址以便交付。试用机是检验产品质量及是否适配您物料的理想方式,建议用于大批量下单前。
55. 能否为机器加装安全防护罩??
部分机型标准配置不含防护罩。应要求,部分机型可加装防护罩,通常增加约1周生产周期。请告知具体型号,我方团队将予以确认。
56. 机器能否采用304不锈钢制造??
多数农用机械主体采用喷漆钢板与铸铁,兼顾强度与经济性。全304不锈钢因成本过高,通常不提供。部分机型有不锈钢版本可选,例如某些搅拌机采用201不锈钢;部分机型可供应不锈钢配件,如大米筛网、研磨盘等。请就您的具体型号咨询我方。
57. 机器是否会生锈??
喷漆钢板与铸铁部件在潮湿或沿海地区可能出现表面锈迹,但不影响正常功能。建议保持机器干燥并遮盖存放,使用后及时清洁,并在裸露金属部位涂抹少量机油。部分机型可供应不锈钢研磨盘与筛网。
58. 易损件通常使用寿命多久??
参考值(正常使用条件下):粉碎机筛网约3–6个月;大米筛网约2–3个月;石磨盘约2–3个月;颗粒机压辊约1–3个月;大米抛光辊约1年。实际寿命受物料硬度、含石量、筛孔尺寸及工作时长影响极大,建议常备易损件。
59. 大米筛网应选择何种材质??
大米筛网提供普通钢、锰钢及硬化不锈钢三种材质。锰钢为标准配置;硬化不锈钢适用于高强度商用场景,寿命更长。筛网易磨损情形包括:稻谷中含石、过量进料、电机功率过大。热处理筛网可能出现变色,属正常现象。
60. 如何为我的机器订购正确的备件??
原文未提供具体操作指引或判断方法。
61. What spare parts kit do you recommend with a new machine?
Grinders: several screens in the sizes you use (for example 2.5, 3, 4, 6 and 8mm) plus hammers or claws. Rice mills: spare rice sieves, a rice roller and belts. Pellet machines: one or two spare dies and a set of rollers. Chaff cutters: a set of blades and belts. An air switch for each electric machine is also recommended. Please request spares before packing so they ship with the machine.
62. Do grinding discs need sharpening, and which discs are available?
Grinding mills use steel discs or stone discs depending on the model, and both are wearing parts. The teeth do not need filing or sharpening; replace the discs when output drops or the flour becomes coarse. Stainless steel discs are available for some models, and plain steel discs may rust, which is normal. Please tell us the disc diameter and number of holes when ordering.
63. How do I run in a new pellet machine?
A new die needs polishing before normal use. Mix about 2.5 to 5kg of sawdust or corn flour with about 1.5 to 2.5kg of fine river sand and 5 to 10 percent edible oil, and feed it slowly until pellets come out smoothly, then start normal feed. Keep the roller-to-die gap at about 0.1 to 0.3mm, and never fill the hopper with dry powder before starting the machine.
64. Which parts of the pellet machine need oil or grease?
The gearbox uses gear oil such as 85W-90 GL-5, not engine oil, filled to the mark before starting. Bearing points with grease nipples need grease, not engine oil. A little oil seepage after the factory test can be normal; tighten the plugs and keep the oil at the correct level without overfilling.
65. How should I fit and tension the belt during assembly?
Mount the motor or engine loosely first, fit the belt, and only then tighten all bolts. The belt should be firm but not overly tight: a belt that is too tight overheats the bearings, and a loose belt slips or falls off. Keep both pulleys aligned in a straight line. Our team can send pictures or a video for your model.
66. How do I install a petrol engine on the machine?
The petrol engine is installed the same way as the electric motor, on the engine frame or base with a matching pulley and belt. An engine version needs the correct frame, so please order the engine version or the engine base together with the machine. We can send installation pictures if you are unsure.
67. How dry should the paddy be for the rice mill?
Paddy should be well dried before milling. Freshly harvested paddy with high moisture produces more broken rice and can block the sieve. Remove stones and sand first and feed evenly. If you still get many broken grains, adjust the outlet gate and milling gap gradually, or try a sieve with a more suitable hole size.
68. The motor hums but does not start, or the breaker trips at start. Why?
Check that the supply voltage and frequency match the motor and that the power source is strong enough, because small generators and inverters often cannot handle the starting current. Make sure nothing is stuck in the machine chamber. If the voltage is correct and the motor only hums, the start capacitor is often faulty; it is an inexpensive part that a local electrician can replace. Send us a video if you are unsure.
69. The rice mill runs but no rice comes out. What should I check?
Check that the motor turns in the correct direction; if not, swap two wires following the wiring diagram. Make sure the rice sieve is installed and aligned with its holes, the outlet gate is open and the belt is not loose. Then adjust the milling gap gradually with the adjusting knob. Our team can send a video for your model.
70. The rice has many broken grains or husk left in it. How can I fix it?
High paddy moisture is the most common cause of broken rice, so dry the paddy well. Adjust the outlet gate and milling knob step by step and feed evenly. If husk remains in the rice, check that the milling gap is not too wide and that the impeller and roller are not worn. Send us a short video with sound so our technician can advise.
71. My rice sieve or grinder screen breaks too quickly. Why?
Sieves and screens are wearing parts. They break faster with stones in the material, overfeeding, very fine holes, loose hammers or bolts, and a motor that is more powerful than the machine needs. Clean the material, feed evenly, check that hammers and bolts are tight, and use a larger hole size where possible. Hardened stainless steel rice sieves last longer in heavy use.
72. The flour from my grinder is too coarse. What can I do?
Fineness is decided by the screen. Fit a smaller screen, for example 0.6mm or 0.8mm, but remember that output falls and wear increases as the hole gets smaller. Claw-type mills with fine screens give finer meal than hammer mills. Also check that the screen is not worn or torn.
73. Dust leaks from the grinder. How can I reduce it?
Check that the feed inlet seal and screen frame are tight, and fit the dust bag at the outlet if your model has one. A worn or soft rubber seal at the inlet can be replaced with a thicker one. Do not overfeed, because overloading pushes dust back out of the inlet.
74. The machine vibrates or the belt keeps coming off. What should I check?
The original text ends here without providing the answer to question 74.
Spare parts identification and compatibility policy?
Send us the model, a clear photo of the machine and nameplate, and the key size. For pellet dies, measure the outer diameter (for example 138mm or 148mm) and hole size; for rice sieves, give length, width and curve; for belts, send the code printed on the belt. Parts from different factories are not interchangeable, so for other brands we need a drawing and cannot always guarantee a fit.
75. My petrol engine will not start. What should I do?
Check that engine oil is at the dipstick mark, because many engines will not start when oil is low, that there is fuel, that the fuel valve is open and that the choke is used for a cold start. If the engine is flooded with fuel, drain the carburetor for about 5 seconds and check the spark plug for a spark. Electric-start engines also need a charged 12V battery.
76. The engine stops after running for a while. Is this normal?
First check fuel and oil levels, because engines stop when fuel runs out or oil is low. In hot weather a heavily loaded engine also gets hot; let it rest for about 20 minutes and avoid overfeeding. If the engine loses power when the hopper is full, feed less material at a time and send us a video.
78. The peanut sheller breaks many kernels. How can I improve it?
Very dry peanuts break easily, so moisten them and let them rest for about 5 hours before shelling. Use a screen that suits your peanut size, open the fan air outlet so husks are blown away, feed slowly and reduce the speed if needed. Also check that the motor turns in the correct direction.
79. The peanut butter or paste machine output is coarse or uneven. What should I check?
Adjust the grinding gap step by step, feed slowly and evenly, and make sure the material is properly roasted or cooked and not damp. Do not connect the motor through an extension board, because low voltage reduces power and heats the motor. Our team can send the English manual and a video.
80. Grass comes out of the bottom of my chaff cutter after assembly. Why?
This usually means a part was assembled in the wrong position. Please send us clear photos of the assembled machine and a short running video, and our technician will show you the correct assembly. Please do not adjust the blades yourself; the 4 moving blades must stay close to the fixed blade.
81. I received fewer cartons than expected. Are parts missing?
One machine is often packed in 3 or more packages (body, hopper, motor or engine), and packages may reach the warehouse separately. Please compare the number of packages with our packing list and tracking numbers and ask your forwarder to check the warehouse. If a part is still missing, send us photos of the opened cartons and labels and we will check and arrange a solution.
82. What is the difference between the proforma invoice and the commercial invoice?
The proforma invoice confirms the order and is used for payment. For customs clearance we issue a commercial invoice and packing list, which do not carry the word proforma. Free spare parts are listed with a reference value, not zero, and motors, screens and other parts are listed so the documents match the goods. Quantities and descriptions on the invoice and packing list always match.
83. Should I choose telex release or an original bill of lading?
Please tell us which your bank or customs requires. A telex release is issued after full payment and lets you collect the goods without paper originals. Original bills of lading are sent by courier, which takes several days. Make sure your forwarder confirms the B/L type in advance so your goods are not held at the port.
84. Customs says the declared value is too low. Can you help?
We declare the true transaction value. If your customs needs supporting evidence, we can provide a supplier declaration on our company letterhead with stamp, showing the goods and prices, and send it to you or your customs broker. We cannot issue invoices that do not match the real price.
85. Can you list every component on the customs documents?
Yes. Some customs offices require all components, such as the motor, screens and capacitors, to be listed, and models and descriptions must match the nameplates. Please tell us your customs requirements before shipment so the commercial invoice and packing list are prepared correctly.
86. Who handles customs clearance and import duties at destination?
Customs clearance, import duties and any import license at the destination are handled by you, your forwarder or your customs broker. We provide the documents they need, such as commercial invoice, packing list, HS code and certificate of origin when requested, and we can follow your customs format as long as the information is accurate.
87. Can you provide a technical data sheet for import approval?
Yes. We can prepare a technical information sheet with model, power, capacity, size and weight on our letterhead with stamp and signature, for example when your importer or authority needs a specification sheet in English or Spanish. Please tell us the format required.
88. Can we communicate on WhatsApp instead of Alibaba.com?
We prefer to keep order communication on Alibaba.com, because quotations, files and payment records stay protected there under Trade Assurance. For large videos that cannot be sent in chat, we can use a video call or email. Our team replies as soon as possible during working hours.
89. What are your working hours?
Our office hours are about 8:30 to 12:00 and 13:00 to 17:30 China time (GMT+8). Because of time differences, messages sent outside these hours are answered on our next working day. You are welcome to leave all your questions in one message so we can answer them together.
90. Am I chatting with a real person or an AI assistant?
Some first replies in our store come from an automated assistant that answers common questions. Quotations, order details and technical problems are handled by our sales team. If you prefer, just ask for a sales representative and your message will be passed on.
大米中残留稻壳,脱壳效果差,可能原因及处理方法??
可能原因:间隙过宽、打谷轮或胶辊磨损。
处理方法:调整间隙;更换磨损的打谷轮或胶辊。
大米中仍有细沙,可能原因及处理方法??
可能原因:分离器仅能去除大于大米尺寸的石子,无法去除细沙。
处理方法:使用清选机或去石机对稻谷进行预清理。
稻谷筛易断裂,可能原因及处理方法??
可能原因:稻谷含石子、进料过快、电机功率过大、每日高强度使用。
处理方法:清选稻谷、均匀进料、选用硬化不锈钢筛、常备备用筛。
设备卡机,可能原因及处理方法??
可能原因:进料过快、反转。
处理方法:通过进料闸门缓慢进料;检查旋转方向。
付款方式与条款?
付款方式包括:(1)Alibaba.com订单链接(Trade Assurance),适用于中小订单,支持信用卡或银行转账等结账页面显示的方式,在线支付币种为美元;(2)汇款至我司公司账户(T/T),适用于大额及整柜订单,银行信息仅以我方正式形式发票(proforma invoice)上印刷的为准,汇款手续费由付款方承担,以确保全额到账;(3)人民币付款(RMB payment in China),可通过您在中国的货代或代理,凭人民币形式发票完成。不接受现金、付至个人账户、个人支付应用(如微信/支付宝)及本地货币付款。
付款条款:小订单及样品需全款预付后安排生产或发货;大额及定制订单通常收取30%定金启动生产,余款须在发货前付清;整柜订单余款可依形式发票约定,在提单(B/L)副本发出后支付。生产自定金到账后启动;余款未结清前货物不予放行,不接受货到目的地后再付款。余款付清前,我方将提供成品机照片与视频,以及带客户 shipping mark 的装箱照片。
Alibaba.com付款实操提示:在线订单(信用卡等)通常可分两期(定金+尾款)支付,银行转账可分多笔;若信用卡有单笔或日限额,我方可按限额拆分为多个独立订单;若支付失败,建议更换信用卡、使用结账页内银行转账(通常1–2个工作日到账),或请银行开通国际线上支付权限;我方可随时重发付款链接;若贵国限制美元支付,可经中国代理协商T/T或RMB付款;付款金额、形式发票与商业发票必须严格一致;订单变更时,我方先更新形式发票及付款链接;装运日期延期需我方说明原因并提交修改申请,客户须在平台「订单」→「全部订单」→对应订单号下确认接受;平台以货物离境中国之日为装运日,延期申请通常仅限一次。
发动机运行后自动停机,可能原因及处理方法??
可能原因:燃油耗尽、机油不足、高温天气或重载下过热。
处理方法:补充燃油、检查机油、停机休息约20分钟、减少进料量。
料斗装满后发动机动力下降,可能原因及处理方法??
可能原因:过载。
处理方法:分次少量进料;确认所配发动机功率与设备匹配。
柴油发动机启动困难,可能原因及处理方法??
可能原因:燃油管路中有空气。
处理方法:按发动机手册排空燃油系统;我方可提供指导视频。
发动机无法安装到机架上,可能原因及处理方法??
可能原因:发动机底座或机架不匹配。
处理方法:订购对应发动机版本或专用发动机底座;安装方式与电机相同。
贸易术语(Trade Terms)责任划分?
我方提供以下贸易术语选项:
- Ex-works:我方在工厂备妥并包装好货物;买方或其货代负责提货及之后所有环节。
- 送货至您在中国的货代仓库:我方负责包装、打标,并将货物送至您指定的中国境内货代仓库,同时提供物流跟踪号及照片;货代负责集拼、出口报关、国际运费、目的港清关及关税。
- FOB(整柜订单):我方负责内陆运输、在约定港口(主要为深圳)装货及出口清关;买方负责订舱、海运费、目的港清关。
- CFR / CIF:应要求报价,仅在具备可靠运输路线时提供;买方负责目的港清关及关税。
- 门到门 / DDP:原则上不提供,仅个别目的地经物流合作伙伴确认可行后个案评估;不适用于多数国家。
我方对交付的责任止于货物送达您在中国的货代仓库(或FOB项下在约定港口装船完毕)。此后由您的货代负责国际运输,我方持续配合提供跟踪号、照片及单据。
国内运输至您在中国的货代仓库流程与时效?
流程:(1)您指定中国境内货代,并向我方提供其仓库地址、电话、入场编号(entry number)及 shipping mark;(2)我方为每件包裹标注您的 shipping mark,并通过国内货运专线送达;(3)我方发送装箱照片(含 shipping mark、每件尺寸与重量、物流单号、仓库收货凭证(如有));(4)您的货代进行集拼并安排出运。
参考时效(自湖南工厂起算):广州约2–3天(通常最近且最经济);佛山、东莞、深圳约2–4天;义乌约3–5天(费用较高);宁波、青岛、上海等更远港口,时效较长,需个案报价。
报价前需提供的信息?
为准确报价,需客户提供以下信息:(1)机型,或待加工物料;(2)每小时所需产量;(3)订购数量;(4)电源规格:电压、相数、频率(50Hz/60Hz及110V/220V/380V电机不同,不可混用);(5)动力类型:电动机、汽油机或柴油机(每台设备仅配一种动力单元);(6)目的港及中国境内货代;(7)品牌标识、颜色或包装等定制需求(定制将延长生产周期)。
国内物流与货运跟踪?
大型或重型机器运输时间可能更长。国内货运线路并非总提供在线追踪服务;我方会提供运单号及货物交付照片。
仓库收货要求?
每件包装须有清晰的唛头,通常包含:报关编号、收货人名称和电话、产品名称、包装件数、目的国或目的港、运输方式(海运SEA或空运AIR);标签须为印刷品、防水且牢固粘贴;无正确唛头的货物可能被拒收。
部分仓库在收货前需提供入库单或仓库入库编号;另一些则要求将装箱单附于货物上。
许多仓库拒收货到付款(COD)包裹、无标签货物、裸装货物及体积过小的包裹。
多数仓库不包含重型物品卸货服务,可能收取叉车或卸货费;卸货前可能需预约。
禁运物品包括:电池、发动机机油和燃油,不得与机器同箱运输;发动机须干式发运。
中国春节及国庆节(10月初)期间,许多货代仓库暂停收货,即使工厂仍在生产。
避免常见交货问题?
发货前须确认准确的仓库信息(城市及详细地址);误送至错误仓库的货物难以追回。
请确保您的货代知晓我方的 shipping mark 及预计包件数量。
若货代测量的总体积(CBM)大于我方装箱单所列数值,请其提供测量记录;我方将重新测量并共享照片。
国际海运时效(参考)?
菲律宾:约20至30天;
欧洲:约40至55天;
西非:约45至90天;
东非和南部非洲:约45至90天;
拉丁美洲及加勒比地区:约45至90天,部分航线更长;
中亚(海陆联运):约2.5至3个月。
以上时效不含目的港清关及内陆运输时间,且因货代、航线及季节而异。拼箱(LCL)服务通常无固定开船日期,海运费率频繁变动。
空运及快递:适用于紧急备件;整机发运时,空运或快递运费通常远高于机器本身价格。
集装箱容量:20英尺柜约27–28 CBM,40HQ柜约60–66 CBM;重型机器可能先达重量上限而非体积上限;我方销售团队将为每个整柜订单制定精确装柜方案。
包装方式?
强韧出口纸箱+捆扎带:用于小型机器;机器本体、料斗和电机通常分装于不同纸箱。
木箱或木架(免熏蒸胶合板):用于颗粒机、组合式碾米机、重型及铸铁类机器;其他机型可应要求加价提供。
编织袋:用于大米筛网等重量大、易压垮纸箱的小型部件。
拉伸膜:部分大型混合机和输送机采用,以节省体积。
包装细节说明?
一台机器通常分多个包件发运,例如本体、料斗和电机;一套组合式碾米机通常发运4–5个包件;请到货后按装箱单核对件数。
机器与电机默认分装;如需合装,须使用木箱。
备件及螺丝装于标有名称的袋子或盒子中;木箱订单中,备件可置于箱内以节省体积。
包装尺寸与重量为预估数值,最终数据以装箱单为准。
应要求,我方可为包件编号(1, 2, 3…)、在每台电机纸箱上标注对应机器名称、加贴“易碎”标签,并提供英文、西班牙文或葡萄牙文标签(替代中文)。
建议长距离、多中转航线使用木箱包装。
碾米机无大米出料,或大米从侧面溢出,可能原因及处理方法??
可能原因:反转、稻谷筛未安装或错位、出料闸门关闭、皮带松弛。
处理方法:纠正旋转方向;按筛孔对齐安装稻谷筛;逐步开启出料闸门;张紧皮带。
大米碎粒过多,可能原因及处理方法??
可能原因:稻谷水分过高、碾磨间隙过紧。
处理方法:干燥稻谷;逐步调节出料闸门与碾磨旋钮。
出口单证与清关?
形式发票(PI):确认型号、配置、数量、价格条款及付款方式;用于付款。
商业发票(CI)与装箱单(PL):用于出运及清关;文件中不出现“proforma”字样;CI与PL上的数量及品名描述须相互一致,且与实物一致。
提单(B/L):整柜订单提供提单草稿供确认;全款到账后签发电放提单(Telex Release);如需正本提单,则通过快递寄送。
原产地证书:应要求提供;需经政府审批,故请预留额外办理时间。
请在出运前告知我方贵方海关具体要求:发票抬头、进口商名称及税号、品名描述语言、HS编码位置及文件格式。
部分海关要求逐项列出所有组件(如电机、筛网、电容等),且机器型号与描述须与铭牌完全一致。
免费备件须按参考价值列明,不可填零。
如海关质疑申报价值,我方可出具加盖公章的公司抬头纸供应商声明;我方始终按真实交易价格申报,无法开具与实际价格不符的发票。
我方可应要求准备技术资料单(含型号、功率、产能、尺寸、重量),以英文或西班牙文出具,加盖公章及签字,用于进口审批。
目的港清关、进口关税及进口许可证由买方、货代或报关行负责。
Mixer 300 kg?
Capacity: About 300 kg pellets or about 260–280 kg powder per batch. Power: 4 kW motor. Voltage: 220V. Machine size: Height about 1700 mm, drum about 930 mm. Weight: —. Packing size: About 110 × 93 × 182 cm. CBM: About 1.86.
生产周期与节假日影响(参考)?
现货标准机型:约3–7个工作日,另加2–5天国内配送;
小批量生产:约7–15天;
整柜订单:定金到账后约3–5周;
特殊60Hz电机:额外增加约1周;
110V或120V电机:耗时显著更长,需逐单确认;
定制颜色或机架:约25–30天;
包装:约2天。
物流延迟常见原因与节前安排提示?
常见延迟原因包括:需特别采购的电机或发动机、中国节假日前的生产旺季、货代截单日期。销售团队会提前告知买家,并分享生产过程照片。
中国需重点规划的节假日:新年(1月初)、春节(约两周,1月或2月,国内物流会提前数日停运)、劳动节(5月初)、国庆节(10月初)。广交会期间(4月和10月)回复可能较慢。请在上述时段前安排付款与交货。
售后支持政策?
我们通常不提供正式保修,因为设备单价较低,而国际运费往往高于设备本身价格。取而代之的是以下支持:
- 出货前测试,并应要求提供测试照片或视频;
- 远程技术指导(通过图片、视频及视频通话);
- 提供英文说明书,以及可获得的组装或操作视频;
- 长期供应备件;
- 建议客户随机器一并订购配套备件包。
我们不派工程师出国安装。大多数设备仅需简单组装,本地电工即可协助接线。
问题申报所需信息?
请提供以下内容:
1. 显示问题的简短视频(带声音);
2. 设备整机、故障部位及电机/发动机铭牌的照片;
3. 设备型号与订单号;
4. 供电电压、电缆截面积与长度、电源接入方式(空开或插头);
5. 加工物料种类及进料方式。
我方技术人员将首先判断问题是否源于电源、装配、操作、物料或零部件。许多问题通过一段视频或几张照片即可解决。如需更换零件,可随下次订单发货(最经济),或通过快递寄送紧急小件。
设备运行中最常见的三类问题原因是什么??
1. 电源连接问题:电机直接插入插座或插线板,未使用空气开关,电缆过长或过细;
2. 电源匹配错误:电压或频率与电机标称值不符(如50Hz vs 60Hz、单相 vs 三相),或所用发电机/逆变器容量不足以承受启动电流;
3. 物料状态问题:颗粒状物料过干或过湿,稻谷过湿或含石子,糊状物料未充分蒸煮或烘烤。
电机通电后嗡嗡响但不启动,且空开跳闸,可能原因及处理方法??
可能原因:电压偏低、电源能力弱、启动电容故障、物料卡在腔体内。
处理方法:检查电压与频率;更换更强力的电源;清理腔体;更换启动电容(成本低,本地电工可安装)。
电机过热或停机,可能原因及处理方法??
可能原因:电缆过长或过细、未接空气开关、过载、连续运转、频率错误。
处理方法:使用2.5mm²或更粗的铜缆,保持电缆短(约8米以内),通过空气开关接入电源,均匀进料,电机发热时暂停运行,确认设备适用50Hz或60Hz。
电机烧毁,可能原因及处理方法??
可能原因:电机直接插电、电压不匹配、使用过细筛网导致严重过载。
处理方法:安装空气开关(及漏电保护器),确认电压匹配,选用合适孔径的筛网。
设备反转(无切割、无吸风、无大米出料),可能原因及处理方法??
可能原因:接线顺序错误。
处理方法:按接线图交换导线或端子连接片。
触摸设备有触电感,可能原因及处理方法??
可能原因:未接地线。
处理方法:使用前务必连接地线。
电机噪音大或振动,可能原因及处理方法??
可能原因:电压不稳定、螺栓松动、轴承磨损、物料卡在腔内。
处理方法:检查电压、拧紧螺栓、清理腔体、避免空载长时间运行;请发送视频以便进一步判断。
汽油发动机无法启动,可能原因及处理方法??
可能原因:无机油(低油保护触发)、燃油阀关闭、未使用阻风门、化油器淹油、无火花。
处理方法:加注机油至油尺刻度线;打开燃油阀;冷机启动时使用阻风门;若淹油,排空化油器约5秒;检查火花塞。
电启动失效,可能原因及处理方法??
可能原因:无电池(电池不随发动机出厂发货)。
处理方法:请在当地购买12V摩托车用电池并安装。
市场适配性说明(欧洲、北美与大洋洲)?
USA:110–120V 60Hz;标准220V设备需定制110V电机或改用汽油机型;多数买家需通过货代收单台设备。
Canada:120/240V 60Hz;240V可安排。
Europe:需本地确认;部分大型设备使用380V三相;欧标插头可按需提供;多数买家需通过货代收单台设备。
Australia:230–240V 50Hz;标准220V 50Hz电机可配本地插头使用。
New Zealand:230V 50Hz;标准220V 50Hz电机适用。
Japan:100V;需特殊电机及本地认证;下单前务必确认。
Feed pellet machine troubleshooting?
New machine only makes powder or blocks — likely cause: Die not run in; hopper filled before starting; action: Run in with sawdust or corn flour, fine river sand and 5 to 10 percent edible oil; start the machine first, then feed slowly. Powder instead of pellets — likely cause: Material too dry, not sticky enough; action: Add a little water or edible oil, or sticky material such as bran or broken corn. Die blocks or machine stalls — likely cause: Material too wet; small die with leafy or soft material; action: Reduce water; use a 4mm die for soft material; clean the die holes. Loose pellets — likely cause: Roller-to-die gap too wide; action: Set the gap to about 0.1 to 0.3mm. Pellets too long or short — likely cause: Cutter setting; action: Adjust the cutter screw: tighten for shorter, loo
sen for longer. Oil seepage — likely cause: Plugs not tight, overfilled, oil left from factory test; action: Tighten plugs, keep oil at the correct level; use 85W-90 GL-5 gear oil, grease at grease nipples. Black material inside a new machine — likely cause: Polishing material from factory testing; action: Normal; it clears during first production. Replacement die does not fit — likely cause: Different die diameter between versions; action: Measure the outer diameter of the old die before ordering.
Grinder, hammer mill, and self-suction grinder troubleshooting?
Flour too coarse — likely cause: Screen too large or worn; hammer mill used for fine flour; action: Fit a smaller screen (for example 0.6mm); use a claw-type mill for finer meal. Low output with fine screen — likely cause: Very fine screen limits flow; action: Use the largest screen that gives acceptable fineness. Screen tears quickly — likely cause: Loose hammers or bolts, hard material, very fine screen; action: Tighten hammers and bolts, use a larger hole, keep spare screens. Self-suction grinder does not suck — likely cause: Reverse rotation, blocked hose; action: Correct rotation; check the hose and rotor turn freely. Dust escapes — likely cause: Worn inlet seal, no dust bag, overfeeding; action: Replace with a thicker rubber seal, fit the dust bag, feed evenly. Belt falls off, loud n
oise — likely cause: Misaligned or unbalanced pulley, loose belt; action: Align pulleys, tension belt, add rubber feet; send a video if it continues.
Grinding disc, paste machine, and wet-material troubleshooting?
Grinding discs wear or rust — likely cause: Normal wear; steel discs can rust; action: Replace discs as wearing parts; stainless discs available for some models; teeth need no filing. Paste coarse or uneven — likely cause: Gap not adjusted, material damp or under-cooked, low voltage; action: Adjust gap step by step, cook or roast properly, feed slowly, no extension board. Grinder cannot process wet material — likely cause: Dry grinders are for dry material only; action: Use a wet and dry grinding mill or paste machine.
Chaff cutter operation and parts troubleshooting?
Cuts long or uneven pieces — likely cause: Gap between moving and fixed blades too large, blades moved; action: Adjust the fixed blade close to the moving blades; the 4 moving blades must stay close to the fixed blade. Loud cutting noise — likely cause: Normal shearing sound of blades; action: Normal; do not adjust blades unless cutting is poor. Grass comes out from the bottom — likely cause: Assembly error; action: Send photos of the assembled machine; we will guide correct assembly. Cutting length cannot be changed — likely cause: Model without gearbox; action: Only gear-type models have length adjustment. Missing small parts after customs inspection — likely cause: Parts loosened during unpacking; action: Check all cartons and the parts bag; send photos so we can identify parts.
Corn sheller and peanut sheller troubleshooting?
Corn sheller cannot grip cobs — likely cause: Cob size differs from inlet setting; action: Adjust the inlet opening with the adjusting handle. Sheller stops often — likely cause: Overfeeding; action: Feed evenly; send a video if it continues. Peanut sheller breaks kernels — likely cause: Peanuts too dry, screen too small, speed too high; action: Moisten peanuts about 5 hours before shelling, use a suitable screen, reduce speed. Husks mixed with kernels — likely cause: Fan outlet closed, feeding too fast; action: Open the fan air outlet, feed slowly.
Mixer and extruder troubleshooting?
Uneven mixing — likely cause: Overfilled; action: Mix smaller, more frequent batches. Wet material sticks — likely cause: Screw mixer used for wet material; action: Use a flat-bottom horizontal mixer for wet material. Extruder blocks or belt overheats — likely cause: Material or settings need adjustment; learning period; action: Adjust material formula (for example add bran) and settings gradually; we provide video guidance.
Shipment issue troubleshooting?
Fewer cartons than expected — likely cause: Packages arriving separately; one machine in several packages; action: Compare with the packing list and tracking numbers; ask the forwarder to check the warehouse. Part appears missing — likely cause: Packed inside another carton or the machine; action: Check all cartons, the parts bag and inside the hopper; send photos of opened cartons. Transport damage — likely cause: Rough handling during transshipment; action: Photograph the damage on receipt and inform your forwarder; we advise on replacement parts; choose wooden cases for long routes. Warehouse refused delivery — likely cause: Wrong or missing shipping mark or entry form; action: Confirm marking requirements with your forwarder; we relabel and redeliver.
Wearing parts and recommended spare kits?
Grinders and hammer mills — main wearing parts: Screens, hammers or claws, belts, bearings; typical life (for reference): Screens about 3 to 6 months. Rice mills — main wearing parts: Rice sieves, rice roller, rice knife, belts; typical life: Sieves about 2 to 3 months; roller about one year. Grinding mills — main wearing parts: Steel or stone discs; typical life: Stone discs about 2 to 3 months. Feed pellet machines — main wearing parts: Flat die, rollers, bearings; typical life: Rollers about 1 to 3 months. Chaff cutters — main wearing parts: Moving and fixed blades, belts, conveyor belt, springs, gears, bearings; typical life: Depends on material and hours.
备件订购与配套建议?
所有电动机器的启动电容需在电机发出嗡嗡声但无法启动时更换。易损件(如筛网、锤片、刀片、压辊、模具、皮带等)寿命取决于材料硬度、物料中是否含沙石、筛孔尺寸及每日工作时长;易损件不享受任何保修,建议客户常备库存。
新订单推荐配套采购以下备件:
- 粉碎机:按您常用规格配置筛网(例如2.5、3、4、6和8mm)及一套锤片或爪片;
- 碾米机:多套碾米筛、一个备用碾米辊及皮带;
- 颗粒机:一至两个您所需规格的备用模具及一套压辊;
- 切草机:一套刀片及皮带;
- 所有电动机器:一个空气开关(MCB)。
随主机同批发货的备件运费远低于后期快递补发。重订备件时,请提供设备型号、清晰照片及关键尺寸(如模具外径、筛网长度/宽度/弧度、皮带型号代码)。其他厂家生产的部件通常不可互换。
电压、相数与频率确认要求?
下单前必须确认收货地的确切电压、相数和频率。不同市场常见供电规格及偏好详见第9–11页表格。例如:非洲多为220–230V 50Hz单相或380V 50Hz三相;菲律宾、拉美多数国家为220V或110V 60Hz;美国为110–120V 60Hz;日本为100V(需特殊电机及本地认证);澳大利亚为230–240V 50Hz;欧洲部分大机型使用380V三相。未确认即下单可能导致电机不匹配或无法使用。
物流与交付方式?
小批量订单:交付至客户指定的中国货代(如广州、佛山或义乌);整柜订单:FOB深圳港,或按双方约定执行。
付款方式与生产流程?
付款方式包括:阿里巴巴平台订单链接支付、公司账户T/T电汇、或通过客户在中国的代理以人民币(RMB)支付。生产于收到定金后启动,余款须在发货前付清。
客户遇到问题时应如何反馈??
请先提供设备运行视频、故障部位照片及铭牌信息(含型号、电压、功率等),以便快速定位问题。
如何获取正式报价??
请提供所需产品型号、数量、目的港及适用电压,销售团队将据此出具正式报价单。
市场适配性说明(非洲)?
Côte d'Ivoire、Benin、Togo、Senegal、Mali、Burkina Faso、Guinea:常见供电为220–230V 50Hz单相;部分地区有380V 50Hz三相;村庄缺稳定电力地区汽油机受欢迎;塞内加尔等法语区使用欧标插头;买家通常通过广州、佛山或义乌货代发货。
Ghana:需本地确认;英标插头(部分买家用南非插头);停电频繁地区需求汽油或柴油机型;面粉加工常需细筛。
Nigeria:230V 50Hz单相;部分地区有230V三相;汽油与柴油机型均有需求。
Cameroon:220V单相;柴油稀缺地区倾向汽油机。
DR Congo:50Hz;因供电不可靠,多选汽油或柴油机型。
Niger及萨赫勒农村地区:常无三相电;推荐发电机、汽油或柴油机型。
Kenya、Tanzania、Uganda:220V 50Hz单相(乌干达为230–240V);偏远地区用汽油机型;常见需求为碾米机、粉碎机、切草机。
Mozambique、Angola:需本地确认;单相更受用户欢迎;柴油机型流行;常要求葡萄牙语标签及铭牌。
South Africa、Namibia、Zimbabwe:依现场而定(单相或380V三相);南非三脚插头;离网用户倾向带电启动功能的柴油机。
Somalia、Somaliland:需本地确认;英标插头或转接器;英文标签;沿海高湿环境,建议防锈处理。
市场适配性说明(亚洲与中东)?
Philippines:220V 60Hz,多为单相;农村地区三相罕见;需60Hz电机;供电不稳定地区用汽油或柴油机型;常见机型为组合式碾米粉碎机、小型碾米机及KL125至KL180颗粒机;旺季为9月至12月。
Indonesia、Vietnam、Cambodia:需本地确认;印尼常要求欧标插头;切草机多为无动力型或配汽油机;碾米机及备用筛网需求多。
India:220V 50Hz单相;大型设备用三相;分销商多采购切草机与颗粒机。
Bangladesh:220V单相常见;部分工业场所为440V 50Hz;选用380V设备前须确认三相电可用性。
Pakistan:大型设备用380V三相;下单前须确认单相或三相供电。
Sri Lanka:400V三相;该电压可兼容380V设备。
Saudi Arabia:220V;大型设备用380V三相;英标插头;需60Hz电机。
Oman:需本地确认;汽油机流行;沿海地区需防锈处理。
Libya:380V 50Hz三相可用;可提供三相机型。
Central Asia(Uzbekistan、Turkmenistan、Kazakhstan):需本地确认;常见需求为切草机与颗粒机;陆运或海陆联运周期长。
市场适配性说明(拉丁美洲与加勒比)?
Venezuela:220V 60Hz,多为单相;部分区域为110V 60Hz;需60Hz电机;主流需求为颗粒机(主用4mm模具)、粉碎机、切草机;汽油与柴油机型均有;美标插头。
Honduras:110V或220V 60Hz单相;商业场所三相为220V 60Hz;农村地区柴油机流行。
Panama:110–120V及220V 60Hz;汽油机型常见;海关常要求完整部件清单。
Ecuador:220V 60Hz单相带接地;亦有110V 60Hz;110V区域推荐柴油机;常需西班牙语技术资料及标签。
Peru:220V 60Hz;需求颗粒机、微型粉碎机及脱粒机;海关要求形式发票(PI)与提单(B/L)描述完全一致。
Colombia、Mexico、El Salvador、Nicaragua、Suriname:110–120V 60Hz常见;部分场所提供220V 60Hz;110V与120V电机交期更长;汽油机为实用替代方案。
Brazil:220V 60Hz;需220V 60Hz电机。
Haiti:110V或220V 60Hz;须按具体场地确认电压。
Mixer 1000 kg?
Capacity: About 1000 kg per batch. Power: 3–4 kW motor. Voltage: 220V or 380V. Machine size: About 175 × 125 × 275 cm; steel plate 1.0 mm (1.8 mm option). Weight: —. Packing size: —. CBM: About 6.
How to choose a thresher (corn, rice, wheat, sorghum, millet, beans)?
Our threshers separate grain from cobs, panicles and straw. For corn, choose a corn peeling-and-threshing machine (peel-free type) if your cobs still have husks, or a mini corn thresher for husked cobs. For rice, wheat, sorghum, millet and beans, choose a multi-crop thresher. Please note that some multi-crop models cannot thresh corn and some rice threshers cannot thresh millet, so tell us your crops before ordering. Small threshers run on a 2.2 kW single-phase motor or a 7–7.5 HP petrol engine; larger models use 4–8 HP diesel engines and can be fitted with wheels for moving between fields. Rice threshers without a built-in fan need a separate winnower for cleaning.
How to choose a vertical screw feed mixer, and what are its limits?
Our vertical screw (spiral) feed mixers mix dry powder, grain meal, premix and pellets evenly in about 2–5 minutes per batch. The model number is the batch size in kilograms. Choose the size by how much feed you mix per batch: 50–100 kg for small farms, 150–300 kg for medium farms and feed lines with a KL160–KL260 pellet machine, and 500–2000 kg for larger farms. Mixers are for dry material only; they are not designed for sugar, very fine fish meal powder or wet material, and they are electric only. Because mixers are tall and light, sea freight is calculated by volume, so please check the CBM of each model when planning shipment. A screw conveyor (auger) is often added to load the mixer or the pellet machine.
Mixer 2000 kg?
Capacity: About 2000 kg per batch. Power: 4 kW motor. Voltage: 220V. Machine size: —. Weight: —. Packing size: Wooden pallet. CBM: —.
Other processing machines – selection guidance?
This section covers other processing machines for poultry, food and post-harvest work: poultry pluckers, peanut butter (nut paste) machines, grain cleaners and winnowers, wood chippers, hand-push seeders and vegetable cutters. These machines are generally designed for small and medium users. Please tell us the material, required output and local power supply so that we can recommend the right model.
Wood chipper WY-WS-200?
Capacity: —. Power: 8 HP petrol. Voltage: —. Machine size: —. Weight: —. Packing size: Wooden case about 121 × 100 × 62 cm. CBM: About 0.75.
Container Loading Reference — How to Use These Figures?
The loading figures come from previous quotations and shipments and are for reference only. The real loading quantity depends on the exact version (with or without motor or engine), packing method, model mix and the weight limit of the shipping line. Small chaff cutters and other heavy, compact machines often reach the container weight limit before the volume is full, while mixers, rice mill lines and large grinders are limited by volume. Our CBM estimates and the forwarder's measured CBM can differ slightly, so please allow some margin. Before an order is confirmed, our sales team will prepare a loading plan with total CBM and gross weight.
Planning values used in quotations: a 20GP holds about 26–28 CBM in practice, and a 40HQ about 64–66 CBM (68 CBM theoretical), with a practical cargo weight of about 28 tonnes for a 40HQ.
For mixed containers, add the per-set CBM of each model from the tables in Chapters 1–7 and keep a margin of about 5–10% for irregular packages such as hoppers, elevators and conveyor boxes.
Full-container Loading References — Chaff Cutters and Silage Choppers?
Reference loading quantities (20GP / 40HQ):
- Hopper-gear chaff cutter, with motor: 20GP about 220 sets; 40HQ about 340 sets.
- 4-blade 3 HP gear chaff cutter: 40HQ about 345 sets with motor; about 455 sets without motor.
- Mini conveyor chaff cutter, 3 HP: about 390 sets (40 ft).
- Small 3 HP chaff cutter (copper motor): 20GP about 130 sets; 40HQ about 400 sets.
- Small chaff cutter without motor: 40HQ about 509–515 sets; limited by about 28 tonnes weight.
- 2-in-1 hopper chaff cutter, without engine: 20GP about 150 sets.
- Manual-feed silage chopper, 0.55 kW: 40HQ about 450 sets.
Full-container Loading References — Threshers, Disc Mills, Grinders and Crushers?
Reference loading quantities (20GP / 40HQ):
- Mini corn thresher with motor (cartons): 40HQ about 894 sets (40 ft).
- Semi-automatic multi-crop peeler-thresher with petrol engine: 40HQ about 190 sets.
- Corn and grain thresher (larger, 81 × 52 × 85.5 cm) with petrol engine: 40HQ about 160 sets.
- Disc mill Model 200 with petrol engine: 20GP about 200–230 sets.
- Disc mill Model 150 head without engine: 20GP about 600 sets.
- G200 grinder with 7 HP petrol engine: 40HQ about 500 sets.
- G-series grinder with zinc-cast head: 40HQ about 900 sets.
- Feed crusher 1000–2000 kg/h with copper motor: 20GP about 190 sets.
Full-container Loading References — Grain Sorter and Rice Mills?
Reference loading quantities (20GP / 40HQ):
- Grain sorter (about 0.31 CBM per set): 20GP about 60–80 sets.
- 6N70 rice mill line (wooden cases): 20GP about 20 sets (about 27 CBM); 40HQ about 50 sets (large 70-type rice mill); limited by volume.
- High-capacity 15 HP diesel rice mill (about 0.9 CBM per set): 40HQ about 40–50 sets.
Batch Volume References — Grinders, Rice Mills and Chaff Cutters?
Batch volume / weight references, useful for LCL and mixed containers:
- Model 26 grinder, 200 sets: about 23 CBM (about 0.115 CBM per set).
- Disc mill Model 150, 150 sets: about 12 CBM / 3750 kg.
- 6N40 rice mill with 3 HP motor, 100 sets: about 13 CBM.
- Combined rice mill (5-in-1), 10 sets: about 1.61 CBM / 680 kg / 21 cartons.
- Combined rice mill with vibrating sieve, 10 sets: about 2.0 CBM / 900 kg.
- Mini conveyor chaff cutter, 10 sets: about 0.95–0.97 CBM / 636 kg.
- 3-in-1 kneading chaff cutter, 10 sets: about 2.47 CBM.
Thresher common wearing parts?
Common wearing parts for our threshers: threshing drum teeth, screens (corn peeling machines have 6 / 10 / 35 mm screens; multi-crop threshers come with about 5 screens for different crops), fan blades, V-belts, pulleys, bearings, sieve plates, rubber rollers for peanut shellers, and engine frame parts. For petrol versions, keep a spare air filter and spark plug; for diesel versions, keep a spare fuel filter.
Batch Volume References — Feed Pellet Machines?
Batch volume / weight references for feed pellet machines (useful for LCL and mixed containers):
- Feed pellet machine KL210, 30 sets: about 11 CBM / 5600 kg.
- Feed pellet machine KL160, 20 sets: about 2.9 CBM / 1760 kg with motor (7 wooden cases, 3 machines per case).
- Feed pellet machine KL125, 20 sets: about 3 CBM.
- Feed pellet machine KL180, 25 sets: about 4.8 CBM / 2700 kg.
- Feed pellet machine KL260, 2 sets: about 1.34 CBM / 560 kg.
Batch Volume References — Grain Grinder, Corn Thresher, Mixers, Fish Feed Extruder and Winnower?
Batch volume / weight references, useful for LCL and mixed containers:
- Universal grain grinder, 10 sets: about 2.6–2.9 CBM / 710 kg.
- Corn peeling and threshing machine, 10 sets: about 1.03 CBM.
- Corn peeling and threshing machine with petrol engine, 15 sets: about 5 CBM (30 cartons).
- Mixer Model 50, 5 sets: about 1.58 CBM.
- Mixer Model 100, 6 sets: about 2.7 CBM.
- Fish feed extruder YH-40, 3 sets: about 4 CBM.
- Winnower, 5 sets: about 1.75 CBM / 190 kg.
Electric-start Engines Shipped Without Battery?
Electric-start engines are shipped without a battery (batteries cannot be shipped as normal cargo); please buy a 12V battery locally.
Engine configuration and ordering notes?
Our standard engine range goes up to about 20–22 HP; larger engines are available on request after confirmation. For multi-machine orders, the same gasoline engine can often be shared between small machines (for example a corn sheller and a peanut sheller) by moving it between frames; please ask us for the right frame and pulley.
Corn peeling and threshing machine (peel-free, MJH10 type)?
Capacity (reference): about 1000–1500 kg/h. Power options: 7–7.5 HP petrol; 0.95–1.8 kW motor; 4 HP diesel option. Voltage: 220V 50/60Hz, 110V or 380V optional. Machine size: —. Weight: machine about 30 kg + petrol engine about 15 kg. Packing size: machine 63 × 48 × 84 cm + engine 39 × 34 × 35 cm. CBM: about 0.3.
Mini corn thresher (gear-adjustable cob size)?
Capacity (reference): above 800 kg/h (up to about 1000 kg/h). Power options: 0.95 kW motor (1.0 / 1.3 / 1.5 HP versions) or 7 HP petrol. Voltage: 220V. Machine size: —. Weight: about 24.3 kg per set (motor version). Packing size: machine 62 × 33 × 27 cm + motor 34 × 22 × 25 cm; petrol version machine 62 × 24 × 26.5 cm + engine 39 × 34 × 35 cm. CBM: about 0.09 (petrol version).
WY-DFJ-80 multi-crop thresher (corn, rice, beans)?
Capacity (reference): about 1–3 t/h (2.2 kW version about 1–1.5 t/h). Power options: 7.5 HP petrol or 2.2 kW motor; 4 HP diesel option. Voltage: 220V. Machine size: about 112.5 × 58.5 × 108.5 cm. Weight: about 102 kg. Packing size: machine 85 × 53 × 87 cm + engine 40 × 35 × 36 cm. CBM: about 0.44–0.5.
5TG-40 double-fan multi-crop thresher?
Capacity (reference): about 500–800 kg/h. Power options: 4 HP petrol, 4 HP diesel or 8 HP hand-start diesel. Voltage: —. Machine size: —. Weight: about 215 kg gross. Packing size: about 141 × 52 × 107 cm. CBM: about 0.78.
5TG-60 double-fan multi-crop thresher?
Capacity (reference): about 800–1000 kg/h. Power options: as 5TG-40 (4 HP petrol, 4 HP diesel or 8 HP hand-start diesel). Voltage: —. Machine size: —. Weight: —. Packing size: —. CBM: —.
Small multi-crop thresher Model 40 / 50 / 60 (rice, rapeseed, wheat)?
Capacity (reference): Model 40 about 500 kg/h; Model 50 about 800 kg/h. Power options: 7.5 HP petrol (with or without wheels). Voltage: —. Machine size: Model 40: 810 × 520 × 855 mm; Model 50: 910 × 520 × 855 mm; Model 60: 1010 × 520 × 855 mm. Weight: Model 40 about 48 kg; Model 50 about 56 kg. Packing size: engine carton 39 × 34 × 35 cm. CBM: —.
Semi-automatic multi-crop peeler-thresher (not for corn)?
Capacity (reference): about 400–600 kg/h (rice above 600, wheat above 400). Power options: 7 HP petrol. Voltage: —. Machine size: —. Weight: machine about 48 kg + engine 14 kg = 62 kg. Packing size: machine 70 × 42.5 × 98 cm (0.3 CBM) + hopper (0.03 CBM) + engine 40 × 34 × 35 cm (0.047 CBM). CBM: about 0.38.
Corn and grain thresher (larger)?
Capacity (reference): about 600 kg/h. Power options: 7.5 HP petrol. Voltage: —. Machine size: —. Weight: about 67 kg. Packing size: about 81 × 52 × 85.5 cm. CBM: about 0.36.
Mini rice thresher (rice only)?
Capacity (reference): about 400 kg/h. Power options: 2.2 kW motor or 7 HP petrol. Voltage: 220V. Machine size: about 850 × 490 × 1580 mm. Weight: about 49 kg. Packing size: —. CBM: —.
WY-TH-40 / WY-TH-50 wheat thresher?
Capacity (reference): about 500 kg/h / 800 kg/h. Power options: 5–6 HP petrol. Voltage: —. Machine size: —. Weight: WY-TH-40 body about 48 kg. Packing size: —. CBM: —.
Peanut sheller (small)?
Capacity (reference): about 200–350 kg/h. Power options: 2.2 kW motor. Voltage: 220V. Machine size: —. Weight: about 58 kg. Packing size: about 69 × 42 × 59 cm. CBM: about 0.17.
Coffee pulper?
Capacity (reference): about 200–300 kg/h. Power options: 1.5 kW motor. Voltage: 220V. Machine size: about 500 × 400 × 1000 mm. Weight: about 62 kg. Packing size: —. CBM: —.
Mixer + grinder unit 2000 kg (cast iron grinding head)?
Capacity: —. Power: Mixer 4 kW + grinder 15 kW. Voltage: 380V. Machine size: About 2330 × 1780 × 2900 mm. Weight: —. Packing size: —. CBM: —.
Screw conveyor 2.5 m (tube 14 cm, height 1.3 m)?
Capacity: About 500 kg/h. Power: 2.2 kW motor. Voltage: 220V. Length: 2.5 m, height 1.3–1.6 m. Weight: —. Packing size: Wooden case about 310 × 54 × 50 cm. CBM: About 0.84.
Mixer series – materials and options?
Mixer materials: carbon steel, galvanised steel or stainless steel (201; 304 on some models). A lid is available for most sizes.
Common wearing parts – mixers and conveyors?
Spiral screw (auger), drum bearings, V-belts and pulleys, discharge gate, lid, motor, and for conveyors the screw flight, tube bearings and hopper.
Poultry plucker Model 60?
Capacity: About 3–4 chickens per batch. Power: 2.2 kW motor, 2800 r/min. Voltage: 220V. Machine size: Drum about 64 × 64 × 86 cm. Weight: About 42 kg. Packing size: About 67 × 67 × 89 cm. CBM: About 0.4.
Poultry plucker Model 80?
Capacity: About 15–16 kg per batch. Power: 3 kW motor. Voltage: 220V. Machine size: —. Weight: —. Packing size: —. CBM: —.
Peanut butter machine Model 100?
Capacity: About 15–30 kg/h depending on material. Power: 1.1 kW copper motor. Voltage: 220V/50Hz (110V/60Hz on request). Machine size: About 26 × 26 × 66 cm. Weight: About 21–23 kg. Packing size: About 33.5 × 34 × 72.5 cm. CBM: About 0.08.
Grain cleaner / grain sorter?
Capacity: About 300–500 kg/h (rated). Power: 1.5 kW motor, 2800 rpm. Voltage: 220V. Machine size: About 1005 × 465 × 675 mm. Weight: About 35 kg. Packing size: About 100 × 46.5 × 66.5 cm. CBM: About 0.31.
WY-WST-120 winnower?
Capacity: Up to about 1.5 t/h (high-capacity version). Power: 1.1 kW (about 2 HP) motor. Voltage: 220V. Machine size: —. Weight: —. Packing size: —. CBM: —.
Hand-push seeder, 1 row?
Capacity: 1–3 seeds per hole. Power: Manual. Voltage: —. Machine size: About 90 × 29 × 29 cm. Weight: About 8.5 kg. Packing size: —. CBM: —.
Hand-push seeder, 3 rows?
Capacity: 1–3 seeds per hole. Power: Manual. Voltage: —. Machine size: About 90 × 42.5 × 35 cm. Weight: About 17.5 kg. Packing size: —. CBM: —.
Petrol rice thresher (no built-in dust removal)?
Capacity (reference): about 200–400 kg/h. Power options: 7.5 HP petrol (fuel about 1 L/h). Voltage: —. Machine size: —. Weight: —. Packing size: machine 95 × 83 × 88 cm + engine 39 × 34 × 35 cm. CBM: about 0.74.
PRT-01 / PRT-02 paddy thresher?
Capacity (reference): above 400 kg/h. Power options: 7.5 HP petrol (no diesel version). Voltage: —. Machine size: —. Weight: —. Packing size: —. CBM: about 0.8 (with engine).
Rice thresher with chassis and wheels?
Capacity (reference): —. Power options: 8 HP water-cooled hand-start diesel. Voltage: —. Machine size: —. Weight: about 290 kg. Packing size: about 140 × 80 × 110 cm. CBM: about 1.23.
Peanut sheller (large)?
Capacity (reference): about 400–500 kg/h. Power options: 3 kW motor or air-cooled diesel. Voltage: 220V. Machine size: —. Weight: —. Packing size: wooden case. CBM: —.
WY-CH-800 coffee huller?
Capacity (reference): about 800 kg/h (coffee beans only). Power options: 1.1 kW motor. Voltage: 220V. Machine size: —. Weight: —. Packing size: wooden case. CBM: about 0.26.
Feed mixer 50 kg?
Capacity (reference): about 50 kg per batch. Power options: 3 kW motor (1.5–2.2 kW versions). Voltage: 220V; 110V/60Hz on request. Machine size: about 64 × 57 × 103 cm (drum about 55 cm). Weight: about 39–44 kg. Packing size: about 64 × 57 × 103 cm. CBM: about 0.38.
Mixer 100 kg?
Capacity: About 80–100 kg per batch. Power: 2.2–3 kW motor. Voltage: 220V; 110V/60Hz on request. Machine size: About 73 × 73 × 98 cm (drum about 73 cm). Weight: About 48 kg. Packing size: About 79 × 78 × 112 cm with wooden frame (or 91 × 73 × 130 cm). CBM: About 0.7–0.86.
Mixer 200 kg?
Capacity: About 200 kg per batch. Power: 4 kW motor. Voltage: 220V (single-phase or 60Hz on request). Machine size: —. Weight: About 68–130 kg depending on packing. Packing size: About 107 × 107 × 128 cm (wooden frame). CBM: About 1.47.
Mixer 500 kg?
Capacity: About 500 kg per batch. Power: 4 kW motor. Voltage: 220V (380V same). Machine size: Height about 205 cm, drum about 102 cm. Weight: Net about 134 kg; gross about 150 kg. Packing size: About 105 × 105 × 227 cm (wooden pallet). CBM: About 2.5.
Screw conveyor 2 m?
Capacity: About 500 kg/h class. Power: 2.2 kW motor. Voltage: 220V. Length: 2 m. Weight: —. Packing size: 3 packages: 220 × 62 × 25 cm + 42 × 24 × 29 cm + 56 × 56 × 60 cm. CBM: —.
Screw conveyor 3 m?
Capacity: —. Power: 2.2 kW motor. Voltage: 220V. Length: 3 m. Weight: About 45–50 kg. Packing size: About 113 × 39 × 84 cm. CBM: About 0.38.
Screw conveyors – tube diameters and power supply?
Tube diameters of 14 or 16 cm are available for screw conveyors. A 12 m conveyor can run on single-phase power; 15 m and longer require three-phase power.
Poultry plucker Model 50?
Capacity: —. Power: 1.5 kW motor, 2800 rpm. Voltage: 220V (110V/60Hz version available). Machine size: —. Weight: —. Packing size: —. CBM: —.
Poultry plucker Model 65?
Capacity: About 10–11 kg (4–5 chickens) per batch. Power: 3 kW motor. Voltage: 220V. Machine size: —. Weight: —. Packing size: About 74 × 74 × 89 cm. CBM: About 0.49.
Poultry pluckers – poultry types and spare parts?
Poultry pluckers handle chickens, ducks and geese; spare rubber fingers are available.
Peanut butter machine Model 160?
Capacity: About 30–60 kg/h depending on material. Power: 1.5 kW motor. Voltage: 220V/50Hz. Machine size: —. Weight: About 42 kg gross (wooden case). Packing size: About 33.5 × 35.5 × 82 cm. CBM: About 0.1.
Winnower?
Capacity: About 500 kg/h. Power: Electric motor. Voltage: 220V. Machine size: —. Weight: About 38 kg per set. Packing size: —. CBM: About 0.35.
Wood chipper Model 150?
Capacity: About 1–2 t/h; branches under about 5 cm. Power: 7 HP petrol. Voltage: —. Machine size: —. Weight: —. Packing size: About 122 × 72 × 102 cm. CBM: About 0.9.
Wood chipper Model 420?
Capacity: —. Power: 7.5 kW or 11 kW motor (made to order). Voltage: 220V/60Hz or 380V. Machine size: —. Weight: —. Packing size: —. CBM: —.
Hand-push seeder, 2 rows?
Capacity: 1–3 seeds per hole. Power: Manual. Voltage: —. Machine size: About 90 × 30.5 × 38 cm. Weight: About 12.5 kg. Packing size: —. CBM: —.
Hand-push seeder, 4 rows?
Capacity: 1–3 seeds per hole. Power: Manual. Voltage: —. Machine size: About 90 × 59 × 35 cm. Weight: About 19.5 kg. Packing size: About 90 × 60 × 32 cm. CBM: —.
Hand-push seeder, 5 rows?
Capacity: 1–3 seeds per hole. Power: Manual. Voltage: —. Machine size: About 90 × 59 × 35 cm. Weight: About 24 kg. Packing size: —. CBM: About 0.075.
Double 7-mouth hand planter?
Capacity: About 0.8–1 mu per hour. Power: Manual. Voltage: —. Machine size: —. Weight: About 8.5 kg. Packing size: About 86 × 46 × 21 cm. CBM: About 0.08.
WBS-36 chip slicer (potato, cassava)?
Capacity: About 300–400 kg/h. Power: 0.55 kW motor, 2800 rpm; 3 blades. Voltage: 220V. Machine size: —. Weight: About 60 kg gross. Packing size: About 60 × 50 × 80 cm. CBM: About 0.24.
Hand-push Seeders (plastic and steel)?
Hand-push seeders (plastic and steel) have row spacing of about 60–120 mm and sowing depth of about 0–50 mm on the multi-row models; the 2-row model has adjustable 6–12 mouths and suits corn, peanuts, soybeans and cotton. Multi-row seeders are best for round seeds such as beans.
Power Options — Electric Motor / Gasoline Engine / Diesel Engine: How to Choose?
Most of our machines can be supplied with an electric motor, a gasoline (petrol) engine or a diesel engine. Choose an electric motor if you have stable grid power: it is quiet, needs little maintenance and gives the most stable output. Choose a gasoline engine for small, mobile machines where there is no electricity; it is light and easy to start. Choose a diesel engine for heavier work, long working hours or larger machines without grid power. Engine versions use a different frame from motor versions, and a belt guard is fitted on diesel versions, so please decide the power type when ordering.
Electric motors (general specifications)?
Winding: 100% copper wire as standard on most machines; a few compact machines use aluminium-wire motors, and the motor specification is always stated in the quotation.
Speed (50Hz): About 2800 r/min (2-pole) for chaff cutters, grinders, threshers and rice mills; about 1400–1440 r/min (4-pole) for pellet machines, mixers and some chilli grinders.
Speed (60Hz): About 3400–3600 r/min (2-pole).
Standard voltage: 220V / 50Hz single-phase for small machines; 380V / 50Hz three-phase for larger machines.
Custom voltage: 220V / 60Hz; 110V / 60Hz (custom-made, about 1 week; not available for some very small motors); 380V / 60Hz; 220V / 60Hz three-phase for countries without 380V; 440V on request.
Single-phase limit: Single-phase motors are used up to about 5.8 kW (KL160 / KL180 pellet machines); hi
gher power needs a three-phase supply.
2.2 kW motor (3 HP): About 23 kg, carton about 45 × 28 × 29 cm (0.036 CBM); single-phase current about 10 A at 220V.
Electrical accessories: Air switch (MCB), forward/reverse switch, voltmeter/ammeter, electric control box for large motors; plugs (EU, UK, US and others) on request.
Gasoline engine 170F (GX200-type)?
Engine: 170F type (GX200-type, 4-stroke, 212 cc). Power (reference): About 6.5–7.5 HP, about 3600 r/min, recoil start (electric start optional). Typical machines: Small chaff cutters, corn shellers, threshers, Model 26 grinder, G200 / MJ disc mills, KL125 / KL150 pellet machines, 6N40 rice mills.
Fuel consumption of the 170F engine is about 1.1–1.4 L/h at full load, 0.7–0.9 L/h at medium load and 0.4–0.6 L/h at idle; the 3.6 L tank lasts about 2.5–3 hours at full load. Engine oil capacity is about 0.5–0.6 L. Gasoline engines are generally not recommended for the larger pellet machines (KL180 and above) because their power is not sufficient.
Diesel engine 168F / 170F / 173 (small air-cooled or water-cooled)?
Engine: Small air-cooled or water-cooled diesel (168F / 170F / 173 types). Power (reference): About 4–8 HP, hand start. Typical machines: Small grinders, chaff cutters, corn shellers, multi-crop threshers, KL150 pellet machine.
Diesel engine 12 HP (192 type)?
Engine: 12 HP diesel (192 type, air-cooled or water-cooled). Power (reference): About 12 HP. Typical machines: 6N70 rice mill, KL210 pellet machine, KL190 pellet machine.
Diesel engine 18–22 HP (electric-start)?
Engine: 18–22 HP electric-start diesel. Power (reference): About 18–22 HP. Typical machines: KL260 pellet machine, Model 350 / large claw grinders.
Matching guide for electric motors and engines (reference)?
Reference matching guide:
Small chaff cutter (0.4–1 t/h) | electric: 2.2 kW single-phase | gasoline: 7–7.5 HP | diesel: 4–8 HP
2–4 t/h chaff cutter | electric: 3–5.5 kW | gasoline: 15 HP | diesel: 6–8 HP
6.5 t/h chaff cutter | electric: 7.5 kW three-phase | gasoline: — | diesel: 15 HP
Model 26 / 9FC-21 grinder | electric: 2.2–3 kW single-phase | gasoline: 7–7.5 HP | diesel: 4–6 HP
Model 28 grinder | electric: 4 kW single-phase | gasoline: 15 HP | diesel: 4–8 HP
9FC-320 / 360 grinder | electric: 7.5–15 kW three-phase | gasoline: — | diesel: 15–22 HP
KL125 / KL150 pellet machine | electric: 3–4 kW single-phase | gasoline: 7.5 HP (KL150) | diesel: About 4–6 HP
KL160 / KL180 pellet machine | electric: 5.8 kW single-phase | gasoline: 15 HP (KL160) | diesel: 8 HP
KL210 / KL230 / KL260 / KL300 |
electric: 7.5 / 11 / 15 / 22 kW three-phase | gasoline: — | diesel: 12 / 15 / 22 / 32 HP
6N40 rice mill and combined rice mill | electric: 2.2–3 kW single-phase | gasoline: 7 HP | diesel: 4 HP
6N70 rice milling line | electric: 7.5 kW + 0.75 kW three-phase | gasoline: Small petrol engine for elevator only | diesel: 12–15 HP + small diesel for elevator
Corn peeling and threshing machine | electric: 0.95–1.8 kW | gasoline: 7–7.5 HP | diesel: 4 HP
Multi-crop thresher | electric: 2.2–3 kW | gasoline: 7.5 HP | diesel: 4–8 HP
Feed mixer | electric: 1.5–4 kW (electric only) | gasoline: — | diesel: —
All power configurations are references. Please confirm the motor or engine, voltage, frequency and phase for your order with our sales team.
Hand-push seeder, 6 rows?
Capacity: 1–3 seeds per hole. Power: Manual. Voltage: —. Machine size: About 90 × 59 × 35 cm. Weight: About 26 kg. Packing size: About 90 × 60 × 32 cm. CBM: About 0.12.
V-01 vegetable shredder?
Capacity: About 150–250 kg/h. Power: 0.75 kW motor, 2800 rpm. Voltage: 220V/50Hz. Machine size: —. Weight: About 24.6 kg. Packing size: About 46 × 37.5 × 73 cm. CBM: About 0.13.
Peanut Butter Machines?
Peanut butter machines grind roasted peanuts, sesame and most nuts into paste. They are designed for about 2–3 hours of continuous work, then a short rest.
Common Wearing Parts (by machine)?
Common wearing parts listed for our machines:
- Rubber plucking fingers.
- Grinding stones (steel and emery) for peanut butter machines.
- Screens and fan for cleaners and winnowers.
- Blades and screens (3 / 5 / 8 / 16 mm) for wood chippers.
- Seed plates, springs and wheels for seeders.
- Slicing, shredding and dicing blades for vegetable cutters.
Electric Motors — Available Power Ratings?
Available power (reference): 2.2 / 3 / 4 / 5.5 / 7.5 / 11 / 15 / 22 / 32 / 35 / 37 kW (smaller 0.55–1.5 kW for small food machines).
Gasoline engine 168F?
Engine: 168F type. Power (reference): About 4 HP. Typical machines: Small grinders, disc mills, small rice mills.
Gasoline engine 190F / 192F?
Engine: 190F / 192F type. Power (reference): About 9–15 HP. Typical machines: KL160 pellet machine, MJ-260 disc mill, wet-and-dry chaff cutters, Model 28 grinder.
Diesel engine 8 HP (water-cooled hand-crank)?
Engine: 8 HP water-cooled hand-crank diesel. Power (reference): About 8 HP. Typical machines: KL160 / KL180 pellet machines, 2–4 t/h chaff cutters, rice threshers with chassis.
Diesel engine 15 HP (hand start)?
Engine: 15 HP diesel (hand start). Power (reference): About 15 HP. Typical machines: 6N70 rice line, KL230 pellet machine, 9FC-320 grinder, 6.5 t/h chaff cutter.
Diesel engine 25–35 HP?
Engine: 25–35 HP diesel. Power (reference): About 25–35 HP. Typical machines: KL300 pellet machine (32 HP), 1 t/h rice unit (25 HP), YH-70 fish feed extruder (32 HP).
Note: A 32 HP diesel uses about 2.4–2.8 L of fuel per hour.
Pellet machine KL400?
The KL400 pellet machine is electric only (37 kW, 380V three-phase).
KL Series Flat-Die Feed Pellet Machines (Selection Guide)?
The KL series flat-die pellet machines press powdered feed (corn meal, bran, grass meal and similar mixtures) into pellets for poultry, pigs, rabbits, sheep, goats and cattle. They are designed for animal feed only and are not suitable for wood or sawdust fuel pellets. The model number refers to the size of the flat die, so a larger number means a larger die, more power and more output. Models KL125 to KL180 can run on 220V single-phase power and are popular for households and small farms; models KL210 to KL400 require 380V three-phase power and are suited to farms and small feed mills. KL125 and KL150 have 2 rollers, KL160 and KL260 have 3 rollers, and KL300 has 4 rollers. KL160 is the best-selling model and is available in a normal (belt) type and a differential type, which runs more smo
othly under load. Each machine is supplied with one die (usually 4 mm) and one set of rollers; dies of 2.5, 3, 4, 6 and 8 mm are available (2.5–3 mm for chicks, fish and pet feed; 4 mm for chickens, ducks and pigs; 6–8 mm for cattle, sheep and horses). Smaller holes give lower output. Please do not add too much water to the material. The 380V models (KL210 and above) are of the differential type; a KL160 upgrade with universal casters is also available.
WY-KL-400 Flat-Die Feed Pellet Machine?
Capacity (reference): about 1000–1250 kg/h. Power options: 37 kW motor, electric only. Voltage: 380V three-phase only. Weight: about 750–880 kg gross. Packing size: wooden case about 183 × 58.5 × 147 cm. CBM: about 1.57. Die diameter (reference): about 398 mm. Pellet length on KL400 is about 1.5–3.5 cm. The 37 kW motor of KL400 must be three-phase; the recommendation is copper cable of at least 25 mm² (50 mm² for runs longer than 25 m) together with an electric control box. This 380V model is of the differential type.
Fish feed extruder YH-40 / WY-PH-40?
Model YH-40 / WY-PH-40: about 40–60 kg/h; 5.5 kW motor; 12 HP diesel option; 220V single-phase (the only single-phase extruder); about 310 kg gross; one case about 157 × 117 × 74 cm (simple assembly on site); CBM about 1.36.
Pellet machines and fish feed extruders – common wearing parts?
Pellet machines: flat die (2.5 / 3 / 4 / 6 / 8 mm), roller set (rollers with bearings), roller shaft, gearbox oil (85W-90 GL-5; about 4.5 L for KL125 and about 5 L for KL160/KL180), V-belts and pulleys, universal casters, air switch (circuit breaker) and electric control box, coupling / universal joint. Fish feed extruders: front and rear screw sleeves, die set, main screw, cutter blades, fuses, cutter motor and reducer. We recommend ordering 1–2 spare dies and one spare roller set with each pellet machine.
Common wearing parts (rice screen, roller, knife, belts, etc.)?
Rice screen (sieve): standard hole 1.2 mm, also 1.0 and 1.5 mm; standard thickness about 1.5 mm, reinforced 1.8 mm; available in iron, manganese steel, stainless steel and hardened stainless steel. Other wearing parts: rice roller (6N40 and 6N70 types), rice shaft, rice knife, bearings, V-belts, pulleys, fan and fan housing, flour screen for the grinder part, grinding discs, start switch and pulley set. Please tell us the machine model when ordering screens, because 6N40, 6N70 and 6N90 screens are different.
9FC-320 (Model 320) claw grinder?
9FC-320 (Model 320) claw grinder: capacity about 500–1000 kg/h; power 7.5 kW motor (11 kW option) or 15 HP diesel; voltage 380V three-phase; weight machine about 188 kg + motor about 107 kg; packing machine 137 × 116 × 67 cm + motor 63.5 × 43.5 × 41 cm (diesel version: machine 152.5 × 61 × 113 cm + engine 77 × 43 × 75 cm); CBM about 1.2 (diesel version about 1.6).
Grinder common wearing parts?
Common wearing parts include screens in hole sizes from fine (about 0.4 mm) to 8 mm (common sizes 0.6 / 0.8 / 1 / 1.2 / 1.5 / 2 / 2.5 / 3 / 3.5 / 5 / 6 / 7 / 8 mm; Model 26 and small grinders use strips of about 760 × 100 mm or 750 × 100 mm; 9NF26 / Model 28 use about 860 mm long strips; 9FC-400 uses about 1260 × 125 mm), screen steel ring and bolts, claw teeth (T-teeth), claw disc, hammer blades, grinding discs (stone/emery pair and steel pair), bearings, V-belts, fan blades, dust bag and cyclone parts. Each grinder is normally supplied with one screen installed (usually 2 mm); we suggest ordering several screens in the sizes you use most.
6N70 automatic rice milling line (electric, with elevator)?
6N70 automatic rice milling line (electric, with elevator): about 500–600 kg/h; rice mill 7.5 kW + elevator 0.75 kW; diesel option 12 HP (mill) + 4 HP (elevator); 380V three-phase (50Hz or 60Hz); installed size about 188 × 130 × 188 cm; main machine about 185 kg (without motor) + elevator about 65 kg; about 335 kg gross; 4 wooden cases: rice mill 72 × 82 × 160 cm, motor 55 × 36 × 55 cm, elevator 37 × 29 × 187 cm and 66 × 46 × 50 cm; CBM about 1.40.
FT-360 hammer mill?
FT-360 hammer mill: power 11 kW motor or 25 HP diesel; voltage 380V; machine size about 1800 × 700 × 1320 mm; weight about 480 kg.
Small chaff cutter "Pro" (conveyor)?
Capacity: About 0.6–1.5 t/h. Power: 2.2 kW motor. Voltage: 220V/60Hz. Packaging: Machine 57 × 49 × 41.5 cm + conveyor 63.5 × 34 × 17 cm + motor carton. Volume: About 0.19.
2-in-1 chaff cutter with potato crusher (4 blades + 10 small blades)?
Capacity: Potato about 300 kg/h; dry grass about 400 kg/h; fresh corn stalk about 1200 kg/h. Power: 2.2 kW motor, 2800 r/min, or 7–7.5 HP petrol. Voltage: 220V. Weight: About 72 kg with motor (petrol version about 68 kg gross). Packaging: Machine 60 × 40 × 31 cm + hopper 38 × 38 × 30 cm + motor 42 × 24 × 29 cm (petrol version adds frame 77 × 77 × 4 cm and engine 39 × 34 × 35 cm). Volume: About 0.15 (petrol version about 0.19).
What functions do the rice mills have?
Our rice mills hull paddy and polish it into white rice; several versions also remove stones and impurities and separate whole rice, broken rice and small stones with a vibrating sieve.
Reference-Only Figures and Pre-Order Confirmation?
All figures in this document are for reference only. Capacity depends on the material, its moisture, the screen or die size and the power configuration. Packing size, gross weight and CBM depend on the version, accessories and packing method (carton, wooden case or wooden frame). Where the records contain several values for the same model, the document shows the most common and most recent one. The final specification, packing list and loading plan must be confirmed with the sales team before an order is placed. Abbreviations used: kW = kilowatt; HP = horsepower; CBM = cubic metre; t/h = tonnes per hour; GP = general purpose container; HQ = high-cube container.
Can the KL series flat-die pellet machines make floating fish feed?
No. The KL series cannot make floating pellets. If floating fish feed is needed, choose a fish feed extruder instead of a flat-die pellet machine.
Fish Feed Extruders (reference section)?
The document contains a section headed "Fish feed extruders (reference)" with a specification table whose columns are: Model, Capacity (reference), Power options, Voltage, Machine size, Weight, Packing size, CBM. In the pages provided no model rows or values are filled in under this table. The document only notes, in the flat-die pellet machine section, that a fish feed extruder should be chosen instead of a flat-die pellet machine when floating fish feed is required.
WY-KL-125 Flat-Die Feed Pellet Machine?
Capacity (reference): about 60–75 kg/h. Power options: 3–4 kW single-phase motor (by configuration); diesel option. Voltage: 220V single-phase; 110V/60Hz on request. Weight: about 81 kg gross. Packing size: wooden case about 81 × 34 × 56 cm. CBM: about 0.15.
WY-KL-150 Flat-Die Feed Pellet Machine?
Capacity (reference): about 75–140 kg/h. Power options: 4 kW motor (1400–1440 rpm); petrol or diesel option. Voltage: 220V single-phase. Weight: about 83 kg gross. Packing size: wooden case about 83 × 34 × 56 cm. CBM: about 0.16. Die diameter (reference): about 138 mm.
WY-KL-160 Flat-Die Feed Pellet Machine?
Capacity (reference): about 100–150 kg/h. Power options: 5.8 kW motor; 15 HP petrol or 8 HP diesel option. Voltage: 220V single-phase; 220V/60Hz, 110V/60Hz or 380V on request. Weight: about 103 kg gross. Packing size: wooden case about 103 × 36 × 62 cm. CBM: about 0.23. Die diameter (reference): about 138 mm (newer version) or 148 mm. The 110V version of KL160 uses a thicker 4 mm² power cable. A KL160 upgrade with universal casters is also available.
WY-KL-160 Diesel Version Flat-Die Feed Pellet Machine?
Capacity (reference): about 100–160 kg/h. Power options: 8 HP water-cooled hand-crank diesel. Voltage: not stated. Weight: about 155–180 kg gross. Packing size: wooden case about 117 × 43 × 83 cm. CBM: about 0.42.
WY-KL-180 Flat-Die Feed Pellet Machine?
Capacity (reference): about 125–160 kg/h. Power options: 5.8 kW motor; 8 HP diesel option. Voltage: 220V single-phase. Weight: about 103 kg gross. Packing size: wooden case about 102 × 32 × 61 cm. CBM: about 0.2. Die diameter (reference): about 138 mm (newer version) or 148 mm.
WY-KL-190 Flat-Die Feed Pellet Machine?
Capacity (reference): about 150–200 kg/h. Power options: 5.5–5.8 kW motor or 12 HP diesel. Voltage: please confirm with sales. CBM: about 0.3. Machine size, weight and packing size are not given in the table.
WY-KL-210 Flat-Die Feed Pellet Machine?
Capacity (reference): about 250–300 kg/h. Power options: 7.5 kW (10 HP) motor, 1400–1440 rpm; 12 HP diesel option. Voltage: 380V three-phase (220V/60Hz three-phase on request). Weight: about 180 kg gross. Packing size: wooden case about 117 × 43 × 83 cm. CBM: about 0.42. Die diameter (reference): about 198 mm. This 380V model is of the differential type.
WY-KL-230 Flat-Die Feed Pellet Machine?
Capacity (reference): about 300–350 kg/h. Power options: 11 kW motor; 15 HP diesel option. Voltage: 380V three-phase. Weight: about 190–205 kg gross. Packing size: wooden case about 130 × 48 × 90 cm. CBM: about 0.56. Die diameter (reference): about 218 mm. This 380V model is of the differential type.
WY-KL-260 Flat-Die Feed Pellet Machine?
Capacity (reference): about 400–500 kg/h. Power options: 15 kW motor, 1400 rpm; 22 HP diesel option. Voltage: 380V three-phase (not single-phase). Weight: about 305 kg gross. Packing size: wooden case about 148 × 52 × 90 cm. CBM: about 0.69. Die diameter (reference): about 248 mm. This model has 3 rollers and is of the differential type.
WY-KL-300 Flat-Die Feed Pellet Machine?
Capacity (reference): about 500–600 kg/h. Power options: 22 kW (about 30 HP) motor; 32 HP diesel option. Voltage: 380V three-phase. Weight: about 420 kg gross (net about 385 kg). Packing size: wooden case about 159 × 59 × 112 cm. CBM: about 1.05. Die diameter (reference): about 298 mm. This model has 4 rollers and is of the differential type.
WY-KL-500 Flat-Die Feed Pellet Machine?
Capacity (reference): about 1500 kg/h. Power options: 55 kW motor. Voltage: 380V three-phase. Machine size: about 216 × 91 × 210 cm. Weight: about 1300 kg. Packing size: please confirm. CBM: not stated. Die diameter (reference): about 498 mm.
Fish feed extruder YH-50?
Model YH-50: 11 kW motor; 380V three-phase; CBM about 1.36.
Fish feed extruder YH-60 / Model 60?
Model YH-60 / Model 60: about 120–150 kg/h; 15 kW main motor + 0.4 kW feeder/cutter motor; 380V (220V/60Hz on request).
Fish feed extruder YH-70 / Model 70?
Model YH-70 / Model 70: about 160–200 kg/h; 18.5 kW motor or 32 HP diesel; 380V (220V/60Hz on request); about 500 kg (diesel version); CBM about 2.1 (diesel version).
Fish feed extruder Model 80?
Model 80: 22 kW motor; upgraded 4-section screw; 380V three-phase; wooden case.
Fish feed extruders – standard dies and diesel note?
Each extruder is normally supplied with 5–6 sets of dies (for example pet food and fish feed dies). Diesel extruders are noisier than electric ones.
6N40 single rice mill (round or square hopper)?
6N40 single rice mill (round or square hopper): about 180–250 kg/h; 2.2 kW (3 HP) motor, 2800 rpm; 7 HP petrol option; 220V single-phase; rice roller Ø40 × 370 mm; machine about 28 kg; motor about 23 kg; packing: machine 57 × 33 × 47 cm (0.089 CBM) + hopper 41 × 42 × 43 cm (0.074 CBM) + motor 45 × 28 × 29 cm (0.036 CBM); CBM about 0.2. Note: 与第3页说法不一致 — Section 2.1 on the same page states about 150–250 kg/h.
Mini rice mill (tall carton version)?
Mini rice mill (tall carton version): about 150–200 kg/h; 2.2 kW motor; 220V/50Hz; about 60 kg; packing: machine 43.5 × 48.5 × 92 cm + motor 45 × 28 × 29 cm; CBM about 0.23.
Model 90 / WY-6N90 rice mill?
Model 90 / WY-6N90: about 180–250 kg/h; 2.2 kW copper motor, 2800 rpm; 220V single-phase; about 58–70 kg per set; packing: machine 52.5 × 33.5 × 56.5 cm + hopper 39 × 39 × 20.5 cm + motor 45 × 28 × 32 cm; CBM about 0.18–0.2.
6NS-16 (3-in-1 household) rice mill?
6NS-16 (3-in-1 household): about 50 kg/h; 2.2 kW; 220V; machine size about 60 × 30 × 70 cm.
6NS-20 (3-in-1 household) rice mill?
6NS-20 (3-in-1 household): about 120 kg/h; 3 kW; 220V; machine size about 85 × 40 × 80 cm.
6NS-200 rice mill?
6NS-200: about 100–150 kg/h; 3 kW (4 kW option); 220V single-phase.
6NS-330 rice mill?
6NS-330: about 450 kg/h; 7.5 kW; 380V three-phase; machine size about 100 × 70 × 120 cm; about 220 kg; CBM about 0.31.
6MS-450 rice mill?
6MS-450: about 1300 kg/h; 18.5 kW; 380V three-phase; machine size about 120 × 85 × 150 cm.
WY-6NF-9 / single-head rice mill with destoner?
WY-6NF-9 / single-head rice mill with destoner: about 300–500 kg/h; 7.5 kW motor or 12 HP diesel; 380V three-phase; installed size about 90 × 45 × 210 cm; about 100 kg (machine); packing: machine wooden case about 76 × 48 × 108 cm + motor 52 × 28 × 29 cm; CBM about 0.44.
6N40-9FC21 multi-function rice mill (rice mill + grinder + vibrating sieve)?
6N40-9FC21 multi-function (rice mill + grinder + vibrating sieve): rice about 170–220 kg/h; grinding about 180–250 kg/h; 2.2 kW motor (rice shaft about 1400 r/min, grinder shaft 4500–5500 r/min); 220V single-phase (380V optional); machine size about 950 × 540 × 1020 mm; about 52 kg net (without motor).
Combined rice mill with grinder (2-in-1 / 5-in-1)?
Combined rice mill with grinder (2-in-1 / 5-in-1): rice about 150–200 kg/h; flour about 180–250 kg/h; 2.2 kW copper motor, 2800 rpm (3 / 3.5 kW and 60Hz optional); 7 HP petrol or 4 HP diesel option; 220V single-phase; installed size about 1580 × 600 × 1300 mm; about 108 kg gross with motor; 6 packages: rice mill 65 × 33 × 57 cm, upper sieve 54.5 × 43.5 × 45.5 cm, side sieve 64 × 32 × 15 cm, pipes 101 × 16 × 9 cm, hopper 42 × 41 × 26 cm, motor 45 × 28 × 29 cm; CBM about 0.35.
6N90-9FC21-200 3-in-1 rice mill (rice mill + crusher + fine grinding)?
6N90-9FC21-200 3-in-1 (rice mill + crusher + fine grinding): rice about 180–250 kg/h; crushing above 250 kg/h; fine grinding above 40 kg/h; 2.2 kW motor; 220V single-phase; machine about 80 kg + motor 23.2 kg; packing: rice mill 75 × 35 × 62 cm + crusher 35 × 28 × 48 cm + motor 45 × 28 × 29 cm + hopper 37 × 37 × 30 cm; CBM about 0.29.
6N70 rice mill, 12 HP diesel, without elevator?
6N70 rice mill, 12 HP diesel, without elevator: about 400–600 kg/h; 12 HP water-cooled diesel; mill about 123 kg + diesel about 95 kg = 218 kg; packing: mill 72 × 65 × 110 cm + diesel 91 × 34 × 57 cm; CBM about 0.69.
Roller corn cracker?
Roller corn cracker: capacity about 2 t/h; power 2.2 kW motor; voltage 220V single-phase; packing about 75 × 65 × 120 cm; CBM about 0.59.
Which rice mill is suitable for households and small villages?
For households and small villages, the 6N40 single rice mill (2.2 kW single-phase) is the usual choice. Section 2.1 states about 150–250 kg/h; the specification table states about 180–250 kg/h. 与第3页说法不一致.
What should I choose if I also need flour?
Choose a combined rice mill with grinder (2-in-1, 3-in-1 or 5-in-1). Note that the rice mill and the grinder of a combined unit should be used one at a time, not at the same time, and after 2–3 hours of continuous work a short rest is recommended.
Which rice mill is suitable for commercial milling services?
For commercial milling services, choose the 6N70 automatic rice milling line (about 500–600 kg/h, reference) with bucket elevator, or the larger WY-6NF-700 unit.
What power supply do rice mills of 7.5 kW and above require?
Machines of 7.5 kW and above require three-phase power (a single-phase supply cannot drive them); diesel versions are available where there is no grid power.
Can the rice screen be used for grinding corn?
No. The rice screen is specific to rice and cannot be used for grinding corn.
6N70 line, diesel, with elevator?
Capacity: about 500–600 kg/h. Power: 12–15 HP diesel plus a small engine for the elevator. Gross weight: about 375 kg. Packing sizes: mill 72 × 82 × 160 cm; elevator 37 × 29 × 187 cm and 66 × 46 × 50 cm; engine 91 × 43 × 75 cm and 45 × 35 × 39 cm. CBM: about 1.6–1.65.
6N70 rice and flour line (with grinder and elevator)?
Capacity: about 500–600 kg/h (rice). Power: 11 kW + elevator 0.75 kW. Voltage: 380V three-phase. Weight: main 185 kg + grinder 55 kg + elevator 65 kg; about 405 kg gross. Packing sizes: mill 72 × 82 × 160 cm; grinder 60 × 44 × 48 cm; elevator feeder 82 × 68 × 69 cm; conveying pipe 203 × 18 × 28 cm; motor 65 × 33 × 29 cm. CBM: about 1.61.
WY-6N70 rice mill with crusher (5-carton set)?
Capacity: about 500–600 kg/h (rice). Power: 7.5 kW copper motor. Voltage: 380V/50Hz three-phase. Total weight: 363 kg. Packing: motor 53 × 35 × 29 cm (72 kg); rice mill 82 × 73 × 163 cm (180 kg); hoister 173 × 32 × 34 cm (42 kg); crusher 80 × 65 × 63 cm (38 kg); other parts 67 × 45 × 40 cm (31 kg). CBM: 1.666.
WY-6NF-700 complete unit?
Capacity: about 600–1000 kg/h depending on paddy and configuration. Power: 7.5 kW motor or 12 HP diesel (key start; battery bought locally). Voltage: 380V three-phase only. Weight: about 300 kg. Packing: 4 packages (wooden cases and cartons). CBM: about 1.5.
1 t/h rice milling unit with elevator?
Capacity: about 1000 kg/h (dry paddy). Power: 15 kW motor + 0.75 kW elevator, or 25 HP diesel. Voltage: 380V/50Hz three-phase. Packing sizes: mill 93 × 59 × 200 cm; hopper frame 110 × 78 × 103 cm; elevator 255 × 32 × 41 cm; diesel 90 × 47 × 70 cm. CBM: about 2.6 (diesel version).
N150?
Power: 18 kW. Voltage: 380V three-phase. No capacity, weight or packing data is given for this model in the source.
N200 (largest 6N type)?
Capacity: about 1800–2000 kg/h. Power: 22 kW. Voltage: 380V three-phase. No weight or packing data is given for this model in the source.
6N70 line – common structure, accessories and use?
The 6N70 line uses a carbon steel and cast iron body with a heat-treated steel roller and direct drive. Standard accessories include the rice hopper, cyclone, dust bag and rice screen. Besides rice, it can be used to dehull corn, quinoa and millet. It does not have a polishing (whitening) function. For the 6N70 line we recommend a generator of about 10–15 kW if no grid power is available.
Elevator (supplied separately)?
The elevator can also be supplied separately: packing about 37 × 29 × 187 cm and 66 × 46 × 50 cm, about 0.4 CBM including a small engine.
FT-320 hammer mill?
FT-320 hammer mill: power 7.5 kW motor or 15–20 HP diesel; voltage 380V; machine size about 1680 × 620 × 1320 mm; weight about 450 kg.
How do I choose among claw-tooth, hammer, self-suction and disc grinders?
Our grinders turn dry grains such as corn, wheat, sorghum, millet, rice and beans into flour or feed meal. Claw-tooth and hammer grinders (Model 26, Model 28, 9FC series) use a screen to control fineness: a smaller screen hole gives finer flour but lower output and more motor load, and a larger hole gives higher output. For general flour a screen of about 1–2 mm is a good choice. Self-suction grinders load the grain through a suction pipe; their motor must turn in the marked direction. Disc mills (MJ-150 / 180 / 200 / 260, G200) grind between stone or steel discs and can process both dry and wet (soaked) material; use steel discs for dry grinding and stone (emery) discs for wet grinding. Claw and hammer grinder
s are for dry material only; they are not suitable for sugar, fresh ginger, fresh chilli, wet soybeans or meat. For small households choose 2.2–3 kW single-phase models; for village mills and small feed mills choose the 9FC-320 / 360 / 400 class, which need 380V three-phase power or a diesel engine.
Model 26 claw + hammer grinder (WY-6NT-26 / 9NT-26)?
Capacity: about 30–300 kg/h depending on screen. Power options: 2.2 kW motor, 2800 rpm; 7.5 HP petrol (3650 rpm) option. Voltage: 220V single-phase; 110V/60Hz on request. Weight: machine about 25.4 kg; about 46 kg with motor. Packing: machine 43 × 34 × 52 cm + motor 42 × 24 × 29 cm (hopper packed separately). CBM: about 0.11 (petrol version about 0.14).
Model 26 self-suction grinder, 3 kW?
Capacity: about 200–300 kg/h. Power: 3 kW motor; 7 HP petrol or 6 HP diesel option. Voltage: 220V single-phase. Grinding chamber about 260 mm. Weight: machine about 39.6 kg + motor about 26 kg. Packing: machine 54 × 38.2 × 52.5 cm + hopper 38 × 65 × 30.5 cm + motor 42 × 24 × 29 cm. CBM: about 0.21 (diesel version about 0.28).
Model 28 self-suction grinder?
Capacity: about 50–500 kg/h depending on screen. Power: 4 kW motor, 2800 rpm; 15 HP petrol or 4–8 HP diesel option. Voltage: 220V single-phase (380V version available). Grinding chamber about 270–280 mm. Packing: machine 58.5 × 44.5 × 58 cm + motor carton. CBM: about 0.24.
9FC-21 grain pulverizer?
Capacity: up to about 300 kg/h. Power: 2.2 kW motor, 2800 rpm; 7 HP petrol option. Voltage: 220V single-phase or 380V. Machine size about 74 × 33 × 92 cm. Weight: about 26–28 kg (machine) + motor 23.2 kg or petrol engine 14 kg. Packing: machine 43 × 34 × 53 cm (0.08 CBM) + motor 45 × 28 × 29 cm (0.037 CBM) or engine 40 × 34 × 35 cm (0.048 CBM). CBM: about 0.12–0.13.
9FQ-20 hammer mill (24 hammers, with cyclone and dust bag)?
Capacity: about 200–350 kg/h (corn). Power: 2.2–3 kW motor, 2800 r/min. Voltage: 220V single-phase. Machine size about 680 × 530 × 1000 mm. Weight: about 45 kg (without motor). Comes with 24 hammers, cyclone and dust bag.
Universal grinder (grain and straw)?
Capacity: about 200–300 kg/h (grain). Power: 3 kW motor. Voltage: 220V. Weight: about 71 kg. Packing: machine 72 × 45 × 48 cm + bin 60 × 50 × 30 cm + motor 45 × 28 × 29 cm. CBM: about 0.29.
G200 disc grinder?
G200 disc grinder: capacity about 100 kg/h; power 7 HP petrol or 2.2–3 kW motor; voltage 220V; weight machine about 28 kg + petrol engine about 14 kg; packing machine 60 × 40 × 52 cm (0.12 CBM) + engine 40 × 34 × 35 cm (0.048 CBM); CBM about 0.16.
MJ-150 disc mill (wet and dry)?
MJ-150 disc mill (wet and dry): capacity about 60–100 kg/h; power 0.75–2.2 kW motor; 170F petrol or diesel option; voltage 220V; weight machine about 21 kg; packing 62 × 33 × 34.5 cm + 27 × 27 × 20 cm; CBM about 0.09.
MJ-180 disc mill?
MJ-180 disc mill: capacity about 50–100 kg/h; power 1.5 kW motor or petrol engine; voltage 220V; machine size height about 81 cm; weight machine about 35 kg; packing machine 57 × 52 × 43 cm + hopper 25 × 25 × 23 cm; CBM about 0.14.
MJ-200 disc mill (disc about 200 mm)?
MJ-200 disc mill (disc about 200 mm): capacity about 100–150 kg/h; power 2.2 kW (3 HP) motor or 7–7.5 HP petrol; voltage 220V; packing about 57 × 37.5 × 50 cm (including petrol engine); CBM about 0.11.
MJ-260 disc mill (cast iron, disc about 260 mm)?
MJ-260 disc mill (cast iron, disc about 260 mm): capacity about 250–500 kg/h depending on material; power 4 kW motor or 15 HP petrol; voltage 380V three-phase (motor version); weight about 85 kg per set; packing machine 57 × 37.5 × 50 cm + petrol engine 49 × 43 × 48 cm; CBM about 0.21 (petrol version).
Model 300 grain mill?
Model 300 grain mill: capacity about 100–800 kg/h; power electric motor; single-phase or three-phase versions; machine size about 850 × 550 × 950 mm; weight about 150 kg; CBM about 0.5.
FT-260 hammer mill?
FT-260 hammer mill: power 4 kW motor or 8 HP diesel; voltage 380V; machine size about 1260 × 480 × 880 mm; weight about 100 kg.
9FC-360 (Model 360) claw grinder?
9FC-360 (Model 360) claw grinder: capacity about 1000–1500 kg/h; power 11 kW motor (15 kW option); voltage 380V three-phase; weight machine about 140 kg; packing wooden case about 145 × 70 × 120 cm; CBM about 1.3.
9FC-400 grinder?
9FC-400 grinder: capacity about 1000–1250 kg/h; power 11–15 kW motor; voltage 380V three-phase; weight about 200 kg; packing wooden case.
Model 350 claw grinder?
Model 350 claw grinder: capacity about 1000–1200 kg/h; power 20–22 HP electric-start diesel; weight about 350 kg gross; packing grinder 162 × 83 × 120 cm + diesel 91 × 44 × 76 cm; CBM about 1.61.
FC500 / Model 500 grinder?
FC500 / Model 500 grinder: capacity about 3.5 t/h; power 22 kW motor or diesel; voltage 380V three-phase; packing wooden case; CBM above 1.0.
Corn cracker (2.5 t/h)?
Corn cracker (2.5 t/h): capacity about 2.5 t/h; power 2.2 kW motor; voltage 220V; weight machine 49 kg + motor 30 kg = 79 kg; packing machine 50 × 44 × 77.5 cm + motor 45 × 28 × 29 cm; CBM about 0.21.
Model 26 grinder?
Model 26 grinder: the Model 26 grinding chamber is carbon steel hardened inside with a wear-resistant cast iron outer layer. On stainless steel versions, only the visible outer parts are stainless steel; the discs and teeth are hardened steel.
9FC-600 grinder?
9FC-600 is a larger 9FC grinder with cyclone; it is available on request.
9FC-700 grinder?
9FC-700 is the largest model among the larger 9FC grinders; it is available on request.
Chaff cutters, kneading machines and forage choppers?
Chaff cutters cut fresh grass, dry hay, straw, corn stalks, sugarcane and small branches (up to about 30 mm) into short pieces for cattle, sheep, goats and rabbits; kneading versions also shred the material into soft fibres that animals eat more easily. Choose the size by daily forage need and power supply. For one or a few animals, the 0.4–1 t/h series (WY-9ZT-0.4A / 0.4C / 0.4Q, hopper-gear and conveyor types) with a 2.2 kW single-phase motor or a 7 HP petrol engine is enough. Gear types allow the cutting length to be adjusted; plain conveyor types have a fixed length. For medium farms, choose 2–3 t/h chain-conveyor or wet-and-dry machines with 3–5.5 kW motors; for large farms choose 3.8–6.5 t/h machines with three-phase motors or diesel engines. 2-in-1 and 3-in-1 machines also crush pot
atoes, cassava and grain, so one machine can prepare both roughage and concentrate.
WY-9ZT-0.4A chaff cutter?
WY-9ZT-0.4A is part of the 0.4–1 t/h chaff cutter series (hopper-gear and conveyor types) for one or a few animals; a 2.2 kW single-phase motor or a 7 HP petrol engine is enough. Gear types allow the cutting length to be adjusted; plain conveyor types have a fixed length.
WY-9ZT-0.4C chaff cutter (conveyor belt, casters)?
WY-9ZT-0.4C chaff cutter (conveyor belt, casters): capacity about 0.4–1 t/h; power 2.2 kW copper motor; 7 HP petrol or diesel option; voltage 220V/50Hz (other voltages on request); weight about 73 kg gross with motor; packing 3 cartons: machine 60 × 40 × 31 cm, motor 40 × 22.5 × 24.5 cm, hopper; CBM about 0.135.
WY-9ZT-0.4Q chaff cutter (petrol version)?
WY-9ZT-0.4Q chaff cutter (petrol version): capacity about 0.6–1 t/h; power petrol engine with recoil start (no battery); weight about 66 kg gross; packing machine 60 × 40 × 31 cm (46.2 kg) + hopper 38 × 38 × 26.5 cm + engine 40 × 35 × 36 cm (14 kg) + engine frame 76 × 53 × 4 cm; CBM about 0.18.
Hopper-gear chaff cutter (universal base)?
Capacity: About 0.4–1.0 t/h. Power: 2.2 kW motor, 2800 rpm; petrol or diesel on the same base. Voltage: 220V. Dimensions: About 1070 × 460 × 880 mm. Weight: Machine about 42 kg + motor about 23 kg. Packaging: Machine 56 × 47 × 33 cm + hopper 60 × 40 × 15 cm + motor 45 × 28 × 29 cm. Volume: About 0.11 (with petrol engine about 0.17).
Mini conveyor-belt chaff cutter (4 blades)?
Capacity: About 0.4–1.0 t/h. Power: 2.2 kW motor, 2800 r/min. Voltage: 220V/50Hz or 60Hz. Dimensions: About 85 × 42 × 78 cm. Weight: Machine about 40 kg + motor 23 kg. Packaging: Machine 55 × 40 × 31 cm + motor 42 × 24 × 29 cm. Volume: About 0.10.
WY-93QS-1 chaff cutter?
Capacity: About 700 kg/h. Power: 2.2 kW motor or 4 HP petrol. Voltage: 220V. Weight: About 55 kg. Volume: About 0.16.
3-in-1 kneading, cutting and grain crushing machine?
Capacity: Grain/kneading about 200 kg/h; fresh corn stalk about 1.0 t/h. Power: 3 kW motor, 2880 r/min; 7.5 HP petrol or 4 HP diesel option. Voltage: 220V. Weight: About 80 kg with motor. Packaging: Machine 78.5 × 46.5 × 56 cm + hopper 70 × 40 × 16 cm + motor 42 × 24 × 29 cm. Volume: About 0.28.
Chain-conveyor chaff cutter, 2 t/h (4 blades, 65Mn, 6 mm)?
Capacity: Grass about 2 t/h; potato about 300 kg/h. Power: 3–4 kW motor, 2800 r/min; 15 HP petrol or diesel option. Voltage: 220V/50Hz. Dimensions: About 1380 × 480 × 980 mm. Weight: About 72–75 kg + motor/engine 26–35 kg. Packaging: Machine 66 × 51 × 36 cm + iron chain conveyor 79 × 45 × 24 cm + motor 45 × 28 × 29 cm. Volume: About 0.24 (engine version about 0.31–0.34).
Large "elephant type" chaff cutter?
Capacity: About 2.5–3 t/h. Power: 4 kW or 5.5 kW motor. Voltage: 220V/60Hz. Packaging: Machine 82 × 53.5 × 107 cm + spare parts 83 × 33 × 44 cm + motor 48.5 × 28 × 29 cm. Volume: About 0.63.
Wet-and-dry chaff cutter (4 moving blades + 32 crushing blades)?
Capacity: About 3–4 t/h; cutting length 1–3 cm. Power: 3 kW or 5.5 kW motor; 15 HP petrol or 8 HP diesel option. Voltage: 220V or 380V. Weight: Machine about 80–100 kg; about 130 kg gross with motor. Packaging: Machine 85 × 46 × 73 cm + iron conveyor 79 × 51 × 23 cm + motor 45 × 28 × 29 cm (wooden case). Volume: About 0.41.
Cutting + kneading + grinding machine (5 moving blades, 5 kneading plates, 16 hammers)?
Capacity: About 4–5 t/h. Power: 3 kW (220V) or 5.5 kW (380V) motor; diesel option. Voltage: 220V or 380V. Dimensions: About 178 × 45 × 158 cm. Weight: About 140 kg gross with motor. Packaging: Machine in 5 packages plus motor. Volume: About 0.78.
9TZ-3G 3-in-1 (cutting, kneading, grain grinding; cyclone dust removal, chain feeding, casters)?
Features: cutting, kneading, grain grinding; cyclone dust removal, chain feeding, casters. Capacity: About 2–4 t/h. Power: 5 kW motor, 2800 r/min. Voltage: 220V/50Hz. Dimensions: About 1930 × 700 × 1080 mm. Weight: About 141 kg.
Large 6.5 t/h chaff cutter, 15 HP diesel?
Capacity: About 6.5 t/h (wet and dry grass). Power: 15 HP hand-start diesel. Packaging: Machine 86.5 × 77 × 54.5 cm + conveyor 125.5 × 70.5 × 37.5 cm + diesel 91 × 43 × 75 cm (wooden cases). Volume: About 0.99.
WY-9QS-0.6S banana tree / cassava cutter (with wheels)?
Capacity: About 700 kg/h. Power: 2.2 kW copper motor or 7 HP petrol. Voltage: 220V/50Hz or 60Hz. Inlet: About 20 cm. Weight: Machine about 31.6 kg + motor about 23 kg. Packaging: Machine 73 × 26 × 58.5 cm + motor 45 × 28 × 32 cm. Volume: About 0.15.
Mini grass cutter?
Capacity: About 200–300 kg/h. Power: 0.75 kW motor. Voltage: 220V. Weight: About 12 kg. Packaging: 34 × 34 × 67 cm. Volume: About 0.08.
WY-9ZT-0.4A small chaff cutter?
WY-9ZT-0.4A has a gear for adjustable cutting length and manual feeding without conveyor. These small machines cut and chop but do not knead.
WY-9ZT-0.4C small chaff cutter?
WY-9ZT-0.4C has a feeding conveyor and fixed cutting length. These small machines cut and chop but do not knead.
WY-9ZT-0.4 small chaff cutter?
WY-9ZT-0.4 has a feeding conveyor and fixed cutting length. These small machines cut and chop but do not knead.
WY-9ZT-0.4Q small chaff cutter?
WY-9ZT-0.4Q has a feeding conveyor and fixed cutting length. These small machines cut and chop but do not knead.
Small chaff cutters (additional materials)?
Small chaff cutters can also dice sweet potato, cassava and corn cobs.
Petrol engine shipping: empty fuel tank?
Petrol engines on small chaff cutters are shipped with an empty fuel tank.
Common wearing parts (chaff cutters)?
Moving blades (65Mn manganese steel, about 220 × 70 mm, 6 mm thick on most models), fixed (counter) blade, kneading blades and hammer blades, triangular small blades, conveyor belt (PVC) or iron chain, large and small gears, V-belts, pulleys, bearings, main shaft, switch set (forward/reverse switch, MCB air switch, ammeter/voltmeter) and screens for crushing models. We recommend keeping one spare set of blades and belts for each machine.
起订量(MOQ)?
MOQ varies by model: chaff cutter (WY-93QS-2) MOQ is 1 carton; maize sheller MOQ is 5 sets; wet/dry corn flour mill MOQ is 2 sets.
你们是铡草机源头生产厂家吗??
Yes, we are the manufacturer — Hunan Weiyan Machinery (VYMOR), producing chaff cutters, grinders, pellet mills, straw splitters, slurry grinders, rice mills, and threshers in our own factory.
付款方式与质保?
Payment terms: 30% deposit + 70% before shipment; warranty: 1 year, excluding wear parts, spare parts and human damage.
铡草机刀片数量配置规则?
标准配置为4个动刀+1个定刀,刀片材质65Mn钢,尺寸220×70×6mm(厚于常见的5mm刀片)。5刀版本需加高机身,仅适用于齿轮式机型;6刀版本最小起订量(MOQ)为50台。另可选配揉丝(kneading/rubbing)刀,使切割后的草料更细软;揉丝刀为可选配置,大型机型(2 t/h及以上)标配揉丝刀。
铡草机动力类型适配规则?
小型铡草机(如9ZT-0.4)支持三种动力形式:2.2kW单相电机(220V/50Hz)、汽油发动机(常用170F,7HP)、小风冷柴油发动机(限170型或更小)。汽油机轴径为20mm,键槽5mm;因汽油机转向与电机相反,需更换对应皮带轮。大型机型(2–6.5 t/h)可配15HP汽油机或12HP柴油机。
铡草机电机功率选型指南?
小机型(4刀,0.4–1 t/h):最低1.8kW(2.4HP),推荐2.2kW(3HP);5刀加宽机型:需3kW;2 t/h链式输送机型:需3.5kW单相电机(约4.5–4.8HP),6.5HP汽油机不满足要求;3–3.8 t/h机型:需5.5kW三相380V电机或15HP汽油机;6–6.5 t/h机型:需12HP柴油机或7.5kW电机。所有标配电机转速约2800rpm;若使用1400rpm电机,链式机型需配≥160mm大皮带轮。
电机转向错误怎么办??
不同型号铡草机对电机转向有特定要求:部分机型需顺时针(CW),部分需逆时针(CCW),例如铡草+粉碎组合机使用逆时针电机;自吸式粉碎机必须顺时针旋转,否则无法吸料并可能过载;米机反转可能导致辊轮螺母松动。外箱已贴旋转方向标识。首次使用前请检查旋转箭头,若方向错误,请联系我方并提供短视频以便确认处理。
小型铡草机可选配件?
可选配件包括:MCB断路开关、正反转开关、功率计量表、移动轮、木箱包装、客户Logo印刷服务。
小型铡草机可选配置与报价规则?
可选配置包括:MCB空气开关(断路器)、正反转开关、电流/电压表、加厚电机皮带轮、1.0mm加厚皮带护罩(标准为0.8mm)、万向轮(swivel casters)、水泵/发动机机架、7层纸箱或木箱、激光雕刻客户logo及客户铭牌。所有可选配置价格均由销售团队随整机一并报价。
小型铡草机装箱尺寸与毛重?
典型小型铡草机装箱数据(机器与电机分装):齿轮型机身约43kg,配电机后总重约66kg;输送带型机身约39kg,纸箱尺寸约550×400×320mm(0.07 CBM),配电机后总重约63kg;9ZT-0.4A机身纸箱约560×460×340mm(0.087 CBM),料斗单独包装;电机箱尺寸450×280×290mm(0.036 CBM,约23kg);整套总CBM约0.1–0.2 CBM,具体以装箱单为准。
小型铡草机集装箱装载数量?
含电机时:20英尺柜约装载175–265台,40HQ柜约375–430台(40HQ通常受重量限制,约27–28吨);不含电机时:20英尺柜约290台,40英尺柜最多约630台。实际数量取决于具体型号、机架类型及纸箱尺寸(如方形加厚底座会减少装载量),最终以订单确认的装箱方案为准。
小型铡草机常见故障如何排查??
Q:齿轮损坏 / 机器发出敲击声 / 运转方向错误。
A:(1)齿轮缺齿或断裂多因运输撞击造成,需更换齿轮;若更换后仍不工作,可能滚轴弯曲。(2)动刀与定刀间发出敲击声,说明刀片间隙调整过紧,需重新调整间隙。(3)运转方向错误:请核对电机旋转方向是否与机身箭头标识一致。建议发送短视频以便我方确认并安排备件。
小型铡草机应订购哪些易损件与备件??
Q:应订购哪些备件?哪些部件容易磨损?
A:小型铡草机常用备件/易损件包括:刀片(220×70×6mm,每台4片)、刀盘总成、V型皮带(常规为A1100;部分型号为A1200/A1250/A1270)、输送带(3mm厚、237mm宽、1100/1200mm长;材质为PVC或带纹理款)、大齿轮(球墨铸铁)、连接齿轮、链条、进料指(feed fingers)、电机皮带轮、料斗/导料槽(hopper/chute)、电机护罩、车轮、电机启动电容(250µF)。请提供机型编号或照片,销售团队将为您报价。
Which chaff cutter capacity to choose?
Q: Which chaff cutter is suitable for my farm? / What capacities do you have? A: Range by capacity: small 9ZT-0.4 series 0.4–1.0 t/h (2.2kW, for small farms); widened 5-blade about 0.8–2 t/h (3kW); 93QS-2 about 2 t/h and 9ZT-2 about 2.5 t/h (3.5kW, with kneading); 3.8 t/h kneading (5.5kW three-phase or 15HP petrol); 6–6.5 t/h (12HP diesel). Kneading machines make the grass softer and finer for cattle and sheep. Please tell us your animal number, material (dry/fresh grass, corn stalk) and power supply so we can recommend a model. We do not have a 10 t/h model. Note: page 5 largest-model answer gives 6.5–8 t/h for the 6.5 t/h model, inconsistent with 6–6.5 t/h here(与第5页说法不一致).
Petrol and diesel engine options?
Q: Which engines can you supply? / What HP is the 170F? A: Engines supplied: 168F petrol about 4HP; 170F petrol about 7HP (nameplate often 7.5HP), 3650rpm; 173F air-cooled diesel about 8HP, about 23–26kg; 177 petrol about 9HP; 190F/192F petrol about 15HP; 192F diesel about 12HP; water-cooled hand-crank diesel 8HP / 12HP (about 102kg) / 15HP (about 150kg); electric-start diesel 22HP / 25HP / 30HP. Tell us the machine and we will recommend. Note: 190F/192F horsepower figures are inconsistent (10hp/14hp/15hp); verify against brochure.
Electric-start diesel battery shipping policy?
Electric-start diesel engines are normally shipped without battery, because batteries cannot be shipped by sea as normal cargo — please buy a battery locally. Page 5 also states: electric-start diesels are shipped without battery (batteries cannot go by sea) — please buy one locally.
Diesel engine start and maintenance tips?
Q: Diesel engine won't start, why? A: Our single-cylinder diesels have no spark plug; they rely on the injector and high-pressure fuel pump. If the engine has not been used for a long time, check injector spray. Please use proper engine oil. Replacing with a bigger engine (e.g. 15HP to 30HP) also needs a new pulley/coupling, belt and reinforced base.
颗粒机电压与相数适配规则?
KL125、KL150 和 KL160 可配置 220V 单相电机;KL210 及以上型号需 380V 三相电源(或柴油发动机);KL180 是否适用单相需向销售团队确认;三相颗粒机电机可按需定制 440V/50Hz;220V/60Hz 和 110V/60Hz 的小型号亦可能提供,但需确认。请提供当地电压、相数和频率。
Can the pellet machine work on 220V single phase? / Do you make 440V or 60Hz?
KL125, KL150 and KL160 can be made with 220V single-phase motors. KL210 and above require 380V three-phase power (or a diesel engine). For KL180, please confirm with our sales team whether single-phase is suitable for your order. Three-phase pellet machine motors can be made in 440V/50Hz on request; 220V/60Hz and 110V/60Hz versions of small models are also possible but need confirmation. Please tell us your local voltage, phase and frequency.
What is the difference between differential type and normal type? / Which pellet machine is better quality?
We offer two drive structures. Back-wheel (coupling) type: the drive shaft is exposed and uses an oil seal; simpler and lighter. Differential type: integrated closed gear transmission, no oil seal needed, more stable, heavier, less load on the motor — better quality, recommended. For KL160 the differential version must use a larger motor. Differential versions are heavier (e.g. KL160 about 160kg, KL150 about 130kg complete).
What pellet size can it make? / Which die for chicken / cattle?
Standard die supplied with the machine is 4mm. Optional dies: 2.5 / 3 / 4 / 5 / 6 / 8mm (2.5mm is the smallest; no 2.2mm). Guide: 2.5–4mm for chicks, ducks, small pigs; 6mm for sheep and calves; 8mm for big cattle and horses. KL180/210 come with 6mm; KL210 can include extra 4mm and 8mm dies. 2.5mm dies cost more (more holes). Keep material moisture about 10–20%. A die normally lasts several months depending on use.
How many rollers does the pellet machine have? / What is the die diameter?
Rollers: KL125 and KL150 have 2 rollers; KL160 has 3 rollers; KL180 has 4 rollers; our KL210 has 3 rollers (a 2-roller version is also possible); KL260 3 rollers; KL300 and KL400 4 rollers. Die diameter: KL150 about 138mm, KL160/KL180 about 148mm (small KL160 version 138mm), KL210 about 210mm. Roller working width on 125/150/160 is about 35–40mm.
Can the pellet machine run on diesel or petrol? / Which engine for KL160?
Yes. Engine options by model: KL150/160 petrol version uses about 7–9HP engines on the back-wheel type; for KL160 a 15HP (190F) petrol engine is recommended — 7HP is on the small side. KL160 diesel versions use 8–9HP diesel (water-cooled available). Model 190 (roller type) can use 8HP petrol. KL210 uses 12HP diesel; KL230 15–18HP; KL260 20–22HP; KL300 32HP diesel. The 500 model cannot use a petrol engine.
What is the packing size of KL160? / How heavy is the pellet machine?
Approximate wooden-case packing: KL125 about 0.14 CBM / 85kg; KL150 83×35×56cm, about 0.14 CBM / 86kg; KL160 about 0.15–0.2 CBM / 88–102kg; KL180 about 103kg; KL210 about 0.38–0.52 CBM / about 230kg; KL230 130×48×82cm, 0.52 CBM / 250kg; KL260 148×55×96cm / about 305kg; KL300 about 1.0 CBM / 500kg; KL400 182×57×153cm, 1.6 CBM / 800kg. Differential versions are heavier. A single wooden case is fumigation-free. Final figures are on the packing list.
颗粒机开关与接线安全规范?
2.2kW 以上颗粒机不配备插头,标配空气开关(断路器),符合行业安全规范;所有颗粒机均配备空气开关;可选配置包括带防尘盒的空气开关、接触器或白色电控箱;安装时禁止使用插头,须使用截面积不少于 4mm² 的铜缆(远距离建议 6mm²),并配 32A 或更大电流断路器;黄绿双色线必须可靠接地;每台电机出厂前均经功率、电流及转向测试。
颗粒机易损件与备件有哪些?是否单独销售模具和压辊??
Q: What spare parts do I need for the pellet mill? / Do you sell dies and rollers?
Can feed pellet machine make wood pellets?
Q: Can your pellet machine make wood/sawdust pellets? / Do you have a biomass pellet machine? A: Our feed pellet machines (KL series) cannot make wood pellets — sawdust needs higher pressure and temperature. For wood/sawdust we supply biomass pellet machines: models 200, 250 and 350, with diesel engines (e.g. 200 with 15HP, 250 with 25HP, 350 with 35HP, about 500kg/h with 8mm die) or an 11kW 380V motor for the 200 model. Each machine includes 2 screens. Feed expanders/extruders (including floating fish feed) are also available on request. 中文:饲料颗粒机打不了木屑,需生物质颗粒机(200/250/350,柴油或电机);另有膨化机。 待核实:参数仅少数来源。
Self-suction grinder model 26 vs 28?
Q: What is the difference between 26 and 28 grinder? / What is the capacity? A: Both are self-suction grain grinders (a hose sucks material in). Model 26: about 250mm grinding chamber, 2.2–3kW (4HP) motor; weight about 48kg with motor, about 0.11–0.13 CBM. Model 28: 280mm chamber, 3–4kW motor, about 500–600kg/h; body about 39kg + motor; about 0.145 CBM. Spare parts of 26 and 28 are not interchangeable. The motor must turn clockwise for suction to work. A manual feeding hopper can be added so it works both ways. 中文:26 型 2.2-3KW、28 型 3-4KW 约 500-600kg/h;配件不通用;必须顺转才能自吸;可加人工料斗。 待核实:26 型产能有 150-180/300-400/350-450kg/h 多种说法,未写入;与宣传册参数核对。
Grinder screen sizes and motor load?
Q: What screen sizes are available? / Can it grind very fine flour? A: For the 26 self-suction grinder, standard screens are 1–6mm, maximum 8mm (no 7mm); fine 0.4mm and 0.6mm are also available (no 0.5mm). Other grinders offer screens from about 0.8mm to 8mm. The smaller the hole, the heavier the motor load — very fine screens (e.g. 0.2mm) need a larger motor to avoid burning it. Custom screen sizes need a minimum of 500 pieces. Spare screens can be ordered with the machine. 中文:26 型筛网 1-6mm 标配、最大 8mm、另有 0.4/0.6;孔越小负载越大,0.2mm 需配大电机;定制筛网 500 起。
不锈钢粉碎机与万能粉碎机 G-series?
Q: Do you have a stainless steel grinder? / Specs of G200? A: Stainless steel pulverizer: 2.2kW copper motor, dry corn about 200–300kg/h, fitted with air switch, no wheels, dry material only (not for wet). G-series universal grinders with stainless hopper: G150 uses about 3HP; G200 uses 2.2kW motor or 7HP petrol, about 40–100kg/h, body about 28–31kg; G260 uses 4kW motor or 15HP petrol, about 100–200kg/h, packing about 72×43×44cm (0.14 CBM). The 8-inch grinder 200 can grind both dry and wet; the 10-inch 260 handles wet beans about 300kg/h. 中文:不锈钢粉碎机 2.2KW 干玉米 200-300kg/h 不能磨湿料;G200 2.2KW/7HP,G260 4KW/15HP。 待核实:G200 产能有 40-80/80-100kg/h 两说;与宣传册参数核对。
Grinder types and suitable materials?
Q: Can the grinder crush corn cob and straw? / Can it grind wet material? A: Choose by material: 9FC-21 grinds grain only (3HP copper motor or 2.2kW). 9ZF-50 grinds grain and also straw/corn cob (3kW copper motor). Claw-type 9TF-320/360 are larger (7.5–11kW, about 900–2000kg/h depending on screen). Suction mill (2.6kW): dry grain and dry chilli only, not wet. Stainless pulverizer: dry only. For wet materials (soaked beans, pastes) use a colloid/grinding mill or the 8/10-inch grinder heads. Please tell us your material and required fineness. 中文:9FC-21 只磨粮食;9ZF-50 可磨粮食和秸秆玉米芯;爪式 320/360 大产能;湿料用磨浆机。 待核实:与宣传册参数核对。
Self-suction grinder overload troubleshooting?
Q: The grinder is hard to run / bearing gets hot / it doesn't suck material. A: Please check: (1) Motor rotation — the self-suction grinder must turn clockwise; reverse rotation causes no suction and heavy load. (2) Turn the rotor by hand with power off to check it moves freely. (3) Screen size — very small holes increase load. (4) Supply voltage and cable size. Send us a short video of the machine running (with sound) and our technician will help diagnose and arrange parts if needed. 中文:检查电机是否顺转、手转是否卡、筛孔是否太小、电压线径;发运行视频给技术排查。 待核实:来源为单次售后反馈。
磨浆机型号区别 150/160/200/260?
Q: What is the difference between grinding mill models? / Can it grind peanut and sesame? A: Model 150: 1.1kW, wet/dry with converter — steel discs for dry, emery (sand) discs for wet; sesame about 15kg/h, peanut/nuts 8–10kg/h, dry grain about 30–60kg/h; carton 57×52×43cm, about 34kg. Model 160: 2.2kW, emery discs only, stainless hopper, about 42kg. Model 200: iron hopper, electric about 48.5kg or petrol about 39kg. Model 260: three-phase motor or 190 petrol engine, about 85kg. Models 150 and 160 can grind dry roasted peanut and sesame. 中文:150 型 1.1KW 干湿两用;160 型 2.2KW 只砂磨不锈钢斗;200 型铁斗;260 三相或汽油。 待核实:150 型干料产量 50kg/h 与画册 30-60kg/h 不一;与宣传册参数核对。
饲料搅拌机订购与物流说明?
Mixers are electric only (no diesel/petrol version). Stainless steel cannot be painted red. Mixers are bulky — shipping is calculated by volume.
碾米机易损件与故障排查?
Wearing parts: rice screen, grinding disc and flour screen. Rice screens come in normal steel, manganese steel, stainless steel and hardened stainless steel; rice rollers are iron only. We also supply shafts, switches, fan assemblies and belts (A/B type). If the shaft breaks or the roller moves sideways, the usual cause is reverse motor rotation loosening the tightening nuts on both sides — correct the rotation and re-tighten the nuts.
木材粉碎机订购与动力建议?
Wood chippers are made to order (no stock). The 168 diesel is not recommended for wood chippers. 原文未给出交期、起订量等更多信息。
非标电压/相数定制起订量?
非标准电压或相数(例如220V三相、大功率单相60Hz电机)必须定制,通常最小起订量约为30–50台。部分小型机器(如26型磨粉机、小型颗粒机、面粉机)已生产过110V/60Hz或220V/60Hz型号——请向销售团队确认当前是否可提供。报价前请务必告知我方所需电压、相数及频率。
CE合规电气安全要求?
为满足CE合规性要求:电机电缆端子须使用金属压接端子(禁止裸露铜线);黄/绿双色线必须作为接地线;功率大于2.2kW的设备须采用空气开关而非插头供电。
Q: 您的切菜机能切丁吗?/ 您有哪些切菜机??
A: 20型窗式切菜机:304不锈钢材质,0.4kW 220V,仅可切片和擦丝(不可切丁),双速;180单头切菜机:1.5kW,产能300–500kg/h,进料口270×200mm,标配3把刀(擦丝3mm、切片3mm、切丁15mm);5-in-1切菜机:切片2–4mm、擦丝2mm、切条及波浪形8/10/14mm、切丁10mm(可选10–25mm);400/500擦丝机:具备切丁、切片、擦丝功能;蔬菜切碎机:201不锈钢材质,铜线电机,配刀片和勺子;另提供备用刀片套装。
Q: 能否做110V 60Hz?/ 我们需要220V三相,可以吗??
A: 标准电机为220V/50Hz单相(用于小型设备)和380V/50Hz三相(用于大型设备)。非标电压或相数(如220V三相、大功率单相60Hz电机)必须定制,通常最小起订量约为30–50台。部分小型设备(如26型磨粉机、小型颗粒机、面粉机)已生产过110V/60Hz或220V/60Hz型号——请向销售团队确认当前是否可提供。报价前请务必告知我方所需电压、相数及频率。
客户询问是否可提供筛网等配件(非整机)?
Yes, we supply spare parts including sieve mesh and grinding discs separately.
Beritahukan model, jumlah, dan tujuan pengiriman Anda
Kami menyusun kutipan harga khusus berikut ketentuan perdagangan (EXW / FOB / CIF). Sampel uji dapat diatur sebelum pesanan massal.















